〜のようにこの問題私はドライブを完全に無視したいのですが、私の場合はシステムにSCSIドライブとして公開されています。私のサーバーの21台のドライブのうち2台が失敗しました。
[2524080.689492] scsi 0:0:90900:0: Direct-Access ATA ST3000DM001-1CH1 CC43 PQ: 0 ANSI: 6
[2524080.689502] scsi 0:0:90900:0: SATA: handle(0x000d), sas_addr(0x5003048001f298cf), phy(15), device_name(0x0000000000000000)
[2524080.689506] scsi 0:0:90900:0: SATA: enclosure_logical_id(0x5003048001f298ff), slot(3)
[2524080.689594] scsi 0:0:90900:0: atapi(n), ncq(y), asyn_notify(n), smart(y), fua(y), sw_preserve(y)
[2524080.690671] sd 0:0:90900:0: tag#1 CDB: Test Unit Ready 00 00 00 00 00 00
[2524080.690680] mpt2sas_cm0: sas_address(0x5003048001f298cf), phy(15)
[2524080.690683] mpt2sas_cm0: enclosure_logical_id(0x5003048001f298ff),slot(3)
[2524080.690686] mpt2sas_cm0: handle(0x000d), ioc_status(success)(0x0000), smid(17)
[2524080.690695] mpt2sas_cm0: request_len(0), underflow(0), resid(0)
[2524080.690698] mpt2sas_cm0: tag(65535), transfer_count(0), sc->result(0x00000000)
[2524080.690701] mpt2sas_cm0: scsi_status(check condition)(0x02), scsi_state(autosense valid )(0x01)
[2524080.690704] mpt2sas_cm0: [sense_key,asc,ascq]: [0x06,0x29,0x00], count(18)
[2524080.690728] sd 0:0:90900:0: Attached scsi generic sg0 type 0
[2524080.691269] sd 0:0:90900:0: [sdb] 5860533168 512-byte logical blocks: (3.00 TB/2.73 TiB)
[2524080.691285] sd 0:0:90900:0: [sdb] 4096-byte physical blocks
[2524111.163712] sd 0:0:90900:0: attempting task abort! scmd(ffff880869121800)
[2524111.163722] sd 0:0:90900:0: tag#2 CDB: Mode Sense(6) 1a 00 3f 00 04 00
[2524111.163729] scsi target0:0:90900: handle(0x000d), sas_address(0x5003048001f298cf), phy(15)
[2524111.163733] scsi target0:0:90900: enclosure_logical_id(0x5003048001f298ff), slot(3)
[2524111.442310] sd 0:0:90900:0: device_block, handle(0x000d)
[2524113.442331] sd 0:0:90900:0: device_unblock and setting to running, handle(0x000d)
[2524114.939280] sd 0:0:90900:0: task abort: SUCCESS scmd(ffff880869121800)
[2524114.939358] sd 0:0:90900:0: [sdb] Write Protect is off
[2524114.939366] sd 0:0:90900:0: [sdb] Mode Sense: 00 00 00 00
[2524114.939444] sd 0:0:90900:0: [sdb] Asking for cache data failed
[2524114.939501] sd 0:0:90900:0: [sdb] Assuming drive cache: write through
[2524114.940380] sd 0:0:90900:0: [sdb] Read Capacity(16) failed: Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK
[2524114.940387] sd 0:0:90900:0: [sdb] Sense not available.
[2524114.940566] sd 0:0:90900:0: [sdb] Read Capacity(10) failed: Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK
[2524114.940570] sd 0:0:90900:0: [sdb] Sense not available.
[2524114.940778] sd 0:0:90900:0: [sdb] Attached SCSI disk
[2524114.984489] mpt2sas_cm0: removing handle(0x000d), sas_addr(0x5003048001f298cf)
[2524114.984494] mpt2sas_cm0: removing : enclosure logical id(0x5003048001f298ff), slot(3)
[2524134.939383] mpt2sas_cm0: log_info(0x31111000): originator(PL), code(0x11), sub_code(0x1000)
[2524134.940116] mpt2sas_cm0: removing handle(0x000e), sas_addr(0x5003048001f298d0)
[2524134.940122] mpt2sas_cm0: removing enclosure logical id(0x5003048001f298ff), slot(4)
[2524153.940404] scsi 0:0:90902:0: Direct-Access ATA ST3000DM001-1CH1 CC43 PQ: 0 ANSI: 6
[2524153.940418] scsi 0:0:90902:0: SATA: handle(0x000d), sas_addr(0x5003048001f298cf), phy(15), device_name(0x0000000000000000)
[2524153.940423] scsi 0:0:90902:0: SATA: enclosure_logical_id(0x5003048001f298ff), slot(3)
[2524153.940699] scsi 0:0:90902:0: atapi(n), ncq(y), asyn_notify(n), smart(y), fua(y), sw_preserve(y)
[2524153.942194] sd 0:0:90902:0: tag#0 CDB: Test Unit Ready 00 00 00 00 00 00
[2524153.942205] mpt2sas_cm0: sas_address(0x5003048001f298cf), phy(15)
[2524153.942208] mpt2sas_cm0: enclosure_logical_id(0x5003048001f298ff),slot(3)
[2524153.942212] mpt2sas_cm0: handle(0x000d), ioc_status(success)(0x0000), smid(12)
[2524153.942214] mpt2sas_cm0: request_len(0), underflow(0), resid(0)
[2524153.942217] mpt2sas_cm0: tag(65535), transfer_count(0), sc->result(0x00000000)
[2524153.942220] mpt2sas_cm0: scsi_status(check condition)(0x02), scsi_state(autosense valid )(0x01)
[2524153.942223] mpt2sas_cm0: [sense_key,asc,ascq]: [0x06,0x29,0x00], count(18)
[2524153.942361] sd 0:0:90902:0: Attached scsi generic sg0 type 0
[2524153.942833] sd 0:0:90902:0: [sdb] 5860533168 512-byte logical blocks: (3.00 TB/2.73 TiB)
[2524153.942840] sd 0:0:90902:0: [sdb] 4096-byte physical blocks
[2524154.190159] scsi 0:0:90903:0: Direct-Access ATA ST3000DM001-1CH1 CC43 PQ: 0 ANSI: 6
[2524154.190174] scsi 0:0:90903:0: SATA: handle(0x0022), sas_addr(0x5003048001ec55ed), phy(13), device_name(0x0000000000000000)
[2524154.190179] scsi 0:0:90903:0: SATA: enclosure_logical_id(0x5003048001ec55ff), slot(1)
[2524154.190368] scsi 0:0:90903:0: atapi(n), ncq(y), asyn_notify(n), smart(y), fua(y), sw_preserve(y)
[2524154.191634] sd 0:0:90903:0: tag#1 CDB: Test Unit Ready 00 00 00 00 00 00
[2524154.191639] mpt2sas_cm0: sas_address(0x5003048001ec55ed), phy(13)
[2524154.191642] mpt2sas_cm0: enclosure_logical_id(0x5003048001ec55ff),slot(1)
[2524154.191645] mpt2sas_cm0: handle(0x0022), ioc_status(success)(0x0000), smid(12)
[2524154.191648] mpt2sas_cm0: request_len(0), underflow(0), resid(0)
[2524154.191651] mpt2sas_cm0: tag(65535), transfer_count(0), sc->result(0x00000000)
[2524154.191654] mpt2sas_cm0: scsi_status(check condition)(0x02), scsi_state(autosense valid )(0x01)
[2524154.191657] mpt2sas_cm0: [sense_key,asc,ascq]: [0x06,0x29,0x00], count(18)
[2524154.191800] sd 0:0:90903:0: Attached scsi generic sg3 type 0
[2524154.192211] sd 0:0:90903:0: [sdd] 5860533168 512-byte logical blocks: (3.00 TB/2.73 TiB)
[2524154.192219] sd 0:0:90903:0: [sdd] 4096-byte physical blocks
私たちの場合、これは古いサーバーであり、アップグレード/修正しないことにしました。今、既存のドライブを取り外さずにそのままにして、アレイを縮小して無効にすることを検討しています。アレイがいっぱいになっていないため、他のサーバーの追加のバックアップ場所としてのみ使用してください。
だから私は怠惰でサーバールームに行きたくありません。このドライブを無効にして続行する方法はありますか？ :-)
このシステムに関する追加情報：
lspci -nn -v -s 05:00.0:
05:00.0 Serial Attached SCSI controller [0107]: LSI Logic / Symbios Logic SAS2308 PCI-Express Fusion-MPT SAS-2 [1000:0087] (rev 05)
Subsystem: LSI Logic / Symbios Logic SAS2308 PCI-Express Fusion-MPT SAS-2 [1000:3020]
Flags: bus master, fast devsel, latency 0, IRQ 29
I/O ports at 7000 [size=256]
Memory at df640000 (64-bit, non-prefetchable) [size=64K]
Memory at df600000 (64-bit, non-prefetchable) [size=256K]
Expansion ROM at df500000 [disabled] [size=1M]
Capabilities: [50] Power Management version 3
Capabilities: [68] Express Endpoint, MSI 00
Capabilities: [d0] Vital Product Data
Capabilities: [a8] MSI: Enable- Count=1/1 Maskable- 64bit+
Capabilities: [c0] MSI-X: Enable+ Count=16 Masked-
Capabilities: [100] Advanced Error Reporting
Capabilities: [1e0] #19
Capabilities: [1c0] Power Budgeting <?>
Capabilities: [190] #16
Capabilities: [148] Alternative Routing-ID Interpretation (ARI)
Kernel driver in use: mpt3sas
Kernel modules: mpt3sas
lsscsi -v:
[0:0:3:0] disk ATA ST3000DM001-1CH1 CC43 /dev/sdc
dir: /sys/bus/scsi/devices/0:0:3:0 [/sys/devices/pci0000:00/0000:00:03.0/0000:05:00.0/host0/port-0:0/expander-0:0/port-0:0:2/end_device-0:0:2/target0:0:3/0:0:3:0]
[0:0:6:0] disk ATA ST3000DM001-1CH1 CC43 /dev/sdf
dir: /sys/bus/scsi/devices/0:0:6:0 [/sys/devices/pci0000:00/0000:00:03.0/0000:05:00.0/host0/port-0:0/expander-0:0/port-0:0:5/end_device-0:0:5/target0:0:6/0:0:6:0]
[0:0:7:0] disk ATA ST3000DM001-1CH1 CC43 /dev/sdg
dir: /sys/bus/scsi/devices/0:0:7:0 [/sys/devices/pci0000:00/0000:00:03.0/0000:05:00.0/host0/port-0:0/expander-0:0/port-0:0:6/end_device-0:0:6/target0:0:7/0:0:7:0]
[0:0:8:0] disk ATA ST3000DM001-1CH1 CC43 /dev/sdh
dir: /sys/bus/scsi/devices/0:0:8:0 [/sys/devices/pci0000:00/0000:00:03.0/0000:05:00.0/host0/port-0:0/expander-0:0/port-0:0:7/end_device-0:0:7/target0:0:8/0:0:8:0]
[0:0:11:0] disk ATA ST3000DM001-1CH1 CC43 /dev/sdi
dir: /sys/bus/scsi/devices/0:0:11:0 [/sys/devices/pci0000:00/0000:00:03.0/0000:05:00.0/host0/port-0:0/expander-0:0/port-0:0:10/end_device-0:0:10/target0:0:11/0:0:11:0]
[0:0:12:0] disk ATA ST3000DM001-1CH1 CC43 /dev/sdj
dir: /sys/bus/scsi/devices/0:0:12:0 [/sys/devices/pci0000:00/0000:00:03.0/0000:05:00.0/host0/port-0:0/expander-0:0/port-0:0:11/end_device-0:0:11/target0:0:12/0:0:12:0]
[0:0:13:0] disk ATA ST3000DM001-1CH1 CC43 /dev/sdk
dir: /sys/bus/scsi/devices/0:0:13:0 [/sys/devices/pci0000:00/0000:00:03.0/0000:05:00.0/host0/port-0:0/expander-0:0/port-0:0:12/end_device-0:0:12/target0:0:13/0:0:13:0]
[0:0:15:0] disk ATA ST3000DM001-1CH1 CC43 /dev/sdl
dir: /sys/bus/scsi/devices/0:0:15:0 [/sys/devices/pci0000:00/0000:00:03.0/0000:05:00.0/host0/port-0:0/expander-0:0/port-0:0:14/end_device-0:0:14/target0:0:15/0:0:15:0]
[0:0:16:0] disk ATA ST3000DM001-1CH1 CC43 /dev/sdm
dir: /sys/bus/scsi/devices/0:0:16:0 [/sys/devices/pci0000:00/0000:00:03.0/0000:05:00.0/host0/port-0:0/expander-0:0/port-0:0:15/end_device-0:0:15/target0:0:16/0:0:16:0]
[0:0:18:0] disk ATA ST3000DM001-1CH1 CC43 /dev/sdn
dir: /sys/bus/scsi/devices/0:0:18:0 [/sys/devices/pci0000:00/0000:00:03.0/0000:05:00.0/host0/port-0:0/expander-0:0/port-0:0:17/end_device-0:0:17/target0:0:18/0:0:18:0]
[0:0:20:0] disk ATA ST3000DM001-1CH1 CC43 /dev/sdo
dir: /sys/bus/scsi/devices/0:0:20:0 [/sys/devices/pci0000:00/0000:00:03.0/0000:05:00.0/host0/port-0:0/expander-0:0/port-0:0:19/end_device-0:0:19/target0:0:20/0:0:20:0]
[0:0:21:0] disk ATA ST3000DM001-1CH1 CC43 /dev/sdp
dir: /sys/bus/scsi/devices/0:0:21:0 [/sys/devices/pci0000:00/0000:00:03.0/0000:05:00.0/host0/port-0:0/expander-0:0/port-0:0:20/end_device-0:0:20/target0:0:21/0:0:21:0]
[0:0:22:0] enclosu LSI CORP SAS2X36 0717 -
dir: /sys/bus/scsi/devices/0:0:22:0 [/sys/devices/pci0000:00/0000:00:03.0/0000:05:00.0/host0/port-0:0/expander-0:0/port-0:0:21/end_device-0:0:21/target0:0:22/0:0:22:0]
[0:0:23:0] disk ATA ST3000DM001-1CH1 CC43 /dev/sdq
dir: /sys/bus/scsi/devices/0:0:23:0 [/sys/devices/pci0000:00/0000:00:03.0/0000:05:00.0/host0/port-0:1/expander-0:1/port-0:1:1/end_device-0:1:1/target0:0:23/0:0:23:0]
[0:0:24:0] disk ATA ST3000DM001-1CH1 CC43 /dev/sdr
dir: /sys/bus/scsi/devices/0:0:24:0 [/sys/devices/pci0000:00/0000:00:03.0/0000:05:00.0/host0/port-0:1/expander-0:1/port-0:1:2/end_device-0:1:2/target0:0:24/0:0:24:0]
[0:0:25:0] disk ATA ST3000DM001-1CH1 CC43 /dev/sds
dir: /sys/bus/scsi/devices/0:0:25:0 [/sys/devices/pci0000:00/0000:00:03.0/0000:05:00.0/host0/port-0:1/expander-0:1/port-0:1:3/end_device-0:1:3/target0:0:25/0:0:25:0]
[0:0:26:0] disk ATA ST3000DM001-1CH1 CC43 /dev/sdt
dir: /sys/bus/scsi/devices/0:0:26:0 [/sys/devices/pci0000:00/0000:00:03.0/0000:05:00.0/host0/port-0:1/expander-0:1/port-0:1:4/end_device-0:1:4/target0:0:26/0:0:26:0]
[0:0:28:0] disk ATA ST3000DM001-1CH1 CC43 /dev/sdu
dir: /sys/bus/scsi/devices/0:0:28:0 [/sys/devices/pci0000:00/0000:00:03.0/0000:05:00.0/host0/port-0:1/expander-0:1/port-0:1:6/end_device-0:1:6/target0:0:28/0:0:28:0]
[0:0:30:0] disk ATA ST3000DM001-1CH1 CC43 /dev/sdw
dir: /sys/bus/scsi/devices/0:0:30:0 [/sys/devices/pci0000:00/0000:00:03.0/0000:05:00.0/host0/port-0:1/expander-0:1/port-0:1:8/end_device-0:1:8/target0:0:30/0:0:30:0]
[0:0:31:0] disk ATA ST3000DM001-1CH1 CC43 /dev/sdx
dir: /sys/bus/scsi/devices/0:0:31:0 [/sys/devices/pci0000:00/0000:00:03.0/0000:05:00.0/host0/port-0:1/expander-0:1/port-0:1:9/end_device-0:1:9/target0:0:31/0:0:31:0]
[0:0:34:0] enclosu LSI CORP SAS2X28 0717 -
dir: /sys/bus/scsi/devices/0:0:34:0 [/sys/devices/pci0000:00/0000:00:03.0/0000:05:00.0/host0/port-0:1/expander-0:1/port-0:1:12/end_device-0:1:12/target0:0:34/0:0:34:0]
[0:0:25856:0]disk ATA ST3000DM001-1CH1 CC43 /dev/sda
dir: /sys/bus/scsi/devices/0:0:25856:0 [/sys/devices/pci0000:00/0000:00:03.0/0000:05:00.0/host0/port-0:0/expander-0:0/port-0:0:14357/end_device-0:0:14357/target0:0:25856/0:0:25856:0]
[0:0:98760:0]disk ATA ST3000DM001-1CH1 CC43 -
dir: /sys/bus/scsi/devices/0:0:98760:0 [/sys/devices/pci0000:00/0000:00:03.0/0000:05:00.0/host0/port-0:0/expander-0:0/port-0:0:60931/end_device-0:0:60931/target0:0:98760/0:0:98760:0]
[2:0:0:0] disk ATA PLEXTOR PX-128M5 1.00 /dev/sdy
dir: /sys/bus/scsi/devices/2:0:0:0 [/sys/devices/pci0000:00/0000:00:1f.2/ata2/host2/target2:0:0/2:0:0:0]
lsscsi -Hv:
[0] mpt2sas
dir: /sys/class/scsi_host//host0
device dir: /sys/devices/pci0000:00/0000:00:03.0/0000:05:00.0/host0
[1] ahci
dir: /sys/class/scsi_host//host1
device dir: /sys/devices/pci0000:00/0000:00:1f.2/ata1/host1
[2] ahci
dir: /sys/class/scsi_host//host2
device dir: /sys/devices/pci0000:00/0000:00:1f.2/ata2/host2
[3] ahci
dir: /sys/class/scsi_host//host3
device dir: /sys/devices/pci0000:00/0000:00:1f.2/ata3/host3
[4] ahci
dir: /sys/class/scsi_host//host4
device dir: /sys/devices/pci0000:00/0000:00:1f.2/ata4/host4
[5] ahci
dir: /sys/class/scsi_host//host5
device dir: /sys/devices/pci0000:00/0000:00:1f.2/ata5/host5
[6] ahci
dir: /sys/class/scsi_host//host6
device dir: /sys/devices/pci0000:00/0000:00:1f.2/ata6/host6
smp_discover /dev/bsg/expander-0:0:
phy 0:S:attached:[500605b00507dd20:03 i(SSP+STP+SMP)] 6 Gbps
phy 1:S:attached:[500605b00507dd20:02 i(SSP+STP+SMP)] 6 Gbps
phy 2:S:attached:[500605b00507dd20:01 i(SSP+STP+SMP)] 6 Gbps
phy 3:S:attached:[500605b00507dd20:00 i(SSP+STP+SMP)] 6 Gbps
phy 12:U:attached:[5003048001f298cc:00 t(SATA)] 6 Gbps
phy 13:U:attached:[5003048001f298cd:00 t(SATA)] 6 Gbps
phy 14:U:attached:[5003048001f298ce:00 t(SATA)] 6 Gbps
phy 17:U:attached:[5003048001f298d1:00 t(SATA)] 6 Gbps
phy 19:U:attached:[5003048001f298d3:00 t(SATA)] 6 Gbps
phy 20:U:attached:[5003048001f298d4:00 t(SATA)] 6 Gbps
phy 21:U:attached:[5003048001f298d5:00 t(SATA)] 6 Gbps
phy 22:U:attached:[5003048001f298d6:00 t(SATA)] 6 Gbps
phy 23:U:attached:[5003048001f298d7:00 t(SATA)] 6 Gbps
phy 25:U:attached:[5003048001f298d9:00 t(SATA)] 6 Gbps
phy 26:U:attached:[5003048001f298da:00 t(SATA)] 6 Gbps
phy 27:U:attached:[5003048001f298db:00 t(SATA)] 6 Gbps
phy 28:U:attached:[5003048001f298dc:00 t(SATA)] 6 Gbps
phy 29:U:attached:[5003048001f298dd:00 t(SATA)] 6 Gbps
phy 31:U:attached:[5003048001f298df:00 t(SATA)] 6 Gbps
phy 32:U:attached:[5003048001f298e0:00 t(SATA)] 6 Gbps
phy 33:U:attached:[5003048001f298e1:00 t(SATA)] 6 Gbps
phy 34:U:attached:[5003048001f298e2:00 t(SATA)] 6 Gbps
phy 35:U:attached:[5003048001f298e3:00 t(SATA)] 6 Gbps
phy 36:D:attached:[5003048001f298fd:00 V i(SSP+SMP) t(SSP)] 6 Gbps
ベストアンサー1
非常に高いSCSIデバイス番号（scsi 0:0:90903:0）は、ハードウェアが絶えず欠落してドライブを再初期化する状況で問題があることを示します。
MPT SASハードウェアはここでほとんどの再初期化を実行するため、カーネルはそれを完全に制御できません。また、21台のドライブがあると言われました。したがって、1つ以上のSASエクスパンダの背後にある可能性があります。
問題は、ソフトウェアを介してSASエクスパンダのポートを無効にできるかどうかです。
エキスパンダーがこれをサポートしている場合（標準ではオプションだと思います）はい！
問題のパッケージはsmp_utils。sg3_utilsも役に立ちます）。
あなたが望むもの：
上記のマンページに従って拡張デバイスを見つけます（おそらく
ls /dev/bsg/expand*）。dmesgによる確認：障害のあるディスクがphyに接続されていることを確認してください
smp_discover /dev/bsg/expander-...。フォームでPHYを無効にします。
smp_phy_control --phy=NN --op=di /dev/bsg/expander-...。あなたのケースに合わせて拡張されました。smp_phy_control --phy=13 --op=di /dev/bsg/expander-0:0 smp_phy_control --phy=15 --op=di /dev/bsg/expander-0:0
phy番号はすでに出力にあります（13、、）。15ただし、を使用して確認する必要がありますsmp_discover。