毎回「ethtool」を手動で実行せずに自動的にインターネット接続を開始する方法

Linuxが起動するたびに、以下の2つのコマンドを手動で使用してインターネットに接続する必要があります。

ethtool -s eth0 autoneg off speed 100 duplex full

ifup eth0

起動後すぐに実行すると、ethtool eth0問題は次のように説明されますLink detected: no。 https://paste.debian.net/hidden/d2b0d461/

このルーターのケーブルを古いDSLルーター接続（別のISPですが、Linuxコンピューターで同じイーサネットケーブルを使用していても）に変更すると、同じLinuxコンピューターが再起動後にインターネット接続を受信するため、他の追加コマンドは必要ありません。

Lubuntuが起動したときに自動的にインターネット接続を開始する方法を探しています。

/etc/ネットワーク/インターフェース:

# This file describes the network interfaces available on your system
# and how to activate them. For more information, see interfaces(5).

source /etc/network/interfaces.d/*

# The loopback network interface
auto lo
iface lo inet loopback

# The primary network interface
#auto eth0
iface eth0 inet dhcp

ethtool -s eth0 autoneg off speed 100 duplex full
allow-hotplug eth0

#iface wlan0 inet manual
#wpa-roam /etc/wpa_supplicant/wpa_supplicant.conf

/etc/rc.local:

#!/bin/sh -e
#
# rc.local
#
# This script is executed at the end of each multiuser runlevel.
# Make sure that the script will "exit 0" on success or any other
# value on error.
#
# In order to enable or disable this script just change the execution
# bits.
#
# By default this script does nothing.

echo 500 > /sys/class/backlight/intel_backlight/brightness
xrandr -s 960x540
rfkill block bluetooth
rfkill block wifi
ethtool -s eth0 autoneg off speed 100 duplex full
ip link set eth0 up
ifup eth0
dhcpcd eth0

exit 0

systemctl status rc-local: 
globalisation@WindowsXP:~$ systemctl status rc-local
● rc-local.service - /etc/rc.local Compatibility
   Loaded: loaded (/lib/systemd/system/rc-local.service; static; vendor preset: 
  Drop-In: /lib/systemd/system/rc-local.service.d
           └─debian.conf
   Active: failed (Result: exit-code) since Sun 2017-06-04 00:31:28 CEST; 15min 
  Process: 636 ExecStart=/etc/rc.local start (code=exited, status=1/FAILURE)

Jun 04 00:31:27 WindowsXP systemd[1]: Starting /etc/rc.local Compatibility...
Jun 04 00:31:28 WindowsXP rc.local[636]: Can't open display
Jun 04 00:31:28 WindowsXP systemd[1]: rc-local.service: Control process exited, 
Jun 04 00:31:28 WindowsXP systemd[1]: Failed to start /etc/rc.local Compatibilit
Jun 04 00:31:28 WindowsXP systemd[1]: rc-local.service: Unit entered failed stat
Jun 04 00:31:28 WindowsXP systemd[1]: rc-local.service: Failed with result 'exit

globalisation@WindowsXP:~$

Lubuntuを起動すると、次のエラーが発生します。

Failed to start LSB: IPV4 DHCP client with IPV4ALL support. See 'systemctl status dhcpcd.service' for details 16.780656 usb 1-1.4.3: device descriptor read/64, error -110

/etc/sysctl.conf:

#
# /etc/sysctl.conf - Configuration file for setting system variables
# See /etc/sysctl.d/ for additional system variables.
# See sysctl.conf (5) for information.
#

#kernel.domainname = example.com

# Uncomment the following to stop low-level messages on console
#kernel.printk = 3 4 1 3

##############################################################3
# Functions previously found in netbase
#

# Uncomment the next two lines to enable Spoof protection (reverse-path filter)
# Turn on Source Address Verification in all interfaces to
# prevent some spoofing attacks
#net.ipv4.conf.default.rp_filter=1
#net.ipv4.conf.all.rp_filter=1

# Uncomment the next line to enable TCP/IP SYN cookies
# See http://lwn.net/Articles/277146/
# Note: This may impact IPv6 TCP sessions too
#net.ipv4.tcp_syncookies=1

# Uncomment the next line to enable packet forwarding for IPv4
#net.ipv4.ip_forward=1

# Uncomment the next line to enable packet forwarding for IPv6
#  Enabling this option disables Stateless Address Autoconfiguration
#  based on Router Advertisements for this host
#net.ipv6.conf.all.forwarding=1


###################################################################
# Additional settings - these settings can improve the network
# security of the host and prevent against some network attacks
# including spoofing attacks and man in the middle attacks through
# redirection. Some network environments, however, require that these
# settings are disabled so review and enable them as needed.
#
# Do not accept ICMP redirects (prevent MITM attacks)
#net.ipv4.conf.all.accept_redirects = 0
#net.ipv6.conf.all.accept_redirects = 0
# _or_
# Accept ICMP redirects only for gateways listed in our default
# gateway list (enabled by default)
# net.ipv4.conf.all.secure_redirects = 1
#
# Do not send ICMP redirects (we are not a router)
#net.ipv4.conf.all.send_redirects = 0
#
# Do not accept IP source route packets (we are not a router)
#net.ipv4.conf.all.accept_source_route = 0
#net.ipv6.conf.all.accept_source_route = 0
#
# Log Martian Packets
#net.ipv4.conf.all.log_martians = 1
#

net.ipv6.conf.all.disable_ipv6 = 1
net.ipv6.conf.default.disable_ipv6 = 1
net.ipv6.conf.lo.disable_ipv6 = 1

これがどのように起こるのかわからない場合は、同じマシン+同じOS（Linuxの場合は設定変更なし）+同じイーサネットケーブルが常に自動的にインターネットを「受信および維持」します（追加の手動コマンドはありません）。 3つの異なるルーターモデルのすべてについて。

4番目の問題のある接続とルーターを除いて、3つの接続とルーターはすべて同じISPで提供されます。

最高の願い。