今日のmdadmメッセージでは、mailRAID1アレイのドライブの1つが障害状態にあります。
余分なドライブがあったので、ドライブの交換に問題はありませんでした。
失敗したドライブを評価する方法を完全に理解していないため、mdadm質問があります。
エラーは明確な状態ですかmdadm、それとも何らかの方法でドライブを回復できますか？
たとえば、を使用してドライブにアクセスし続けることができるので、gdiskドライブが技術的にまだ死んでいるわけではないので、これについてお問い合わせください。
詳細：
mdadm --detail /dev/md1
出力：
/dev/md1:
Version : 1.2
Creation Time : Sun Mar 26 17:25:30 2017
Raid Level : raid1
Array Size : 976630464 (931.39 GiB 1000.07 GB)
Used Dev Size : 976630464 (931.39 GiB 1000.07 GB)
Raid Devices : 2
Total Devices : 2
Persistence : Superblock is persistent
Intent Bitmap : Internal
Update Time : Mon Oct 2 07:31:25 2017
State : clean, degraded
Active Devices : 1
Working Devices : 1
Failed Devices : 1
Spare Devices : 0
Name : backup-server:1 (local to host backup-server)
UUID : 319334f9:76d6fccf:d61307bd:2427b6ba
Events : 13023
Number Major Minor RaidDevice State
0 8 49 0 active sync /dev/sdd1
- 0 0 1 removed
1 8 65 - faulty /dev/sde1
そして
hdparm -I /dev/sde
出力：
/dev/sde:
ATA device, with non-removable media
Model Number: WDC WD1002F9YZ-09H1JL1
Serial Number: WD-WMC5K0D33MEU
Firmware Revision: 01.01M03
Transport: Serial, SATA 1.0a, SATA II Extensions, SATA Rev 2.5, SATA Rev 2.6, SATA Rev 3.0
Standards:
Supported: 8 7 6 5
Likely used: 8
Configuration:
Logical max current
cylinders 16383 16383
heads 16 16
sectors/track 63 63
--
CHS current addressable sectors: 16514064
LBA user addressable sectors: 268435455
LBA48 user addressable sectors: 1953525168
Logical Sector size: 512 bytes
Physical Sector size: 4096 bytes
Logical Sector-0 offset: 0 bytes
device size with M = 1024*1024: 953869 MBytes
device size with M = 1000*1000: 1000204 MBytes (1000 GB)
cache/buffer size = unknown
Form Factor: 3.5 inch
Nominal Media Rotation Rate: 7200
Capabilities:
LBA, IORDY(can be disabled)
Queue depth: 32
Standby timer values: spec'd by Standard, with device specific minimum
R/W multiple sector transfer: Max = 16 Current = 0
Advanced power management level: 128
DMA: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 udma4 udma5 *udma6
Cycle time: min=120ns recommended=120ns
PIO: pio0 pio1 pio2 pio3 pio4
Cycle time: no flow control=120ns IORDY flow control=120ns
Commands/features:
Enabled Supported:
* SMART feature set
Security Mode feature set
* Power Management feature set
* Write cache
* Look-ahead
* WRITE_BUFFER command
* READ_BUFFER command
* NOP cmd
* DOWNLOAD_MICROCODE
* Advanced Power Management feature set
Power-Up In Standby feature set
* SET_FEATURES required to spinup after power up
* 48-bit Address feature set
* Mandatory FLUSH_CACHE
* FLUSH_CACHE_EXT
* SMART error logging
* SMART self-test
* General Purpose Logging feature set
* WRITE_{DMA|MULTIPLE}_FUA_EXT
* 64-bit World wide name
* IDLE_IMMEDIATE with UNLOAD
* WRITE_UNCORRECTABLE_EXT command
* {READ,WRITE}_DMA_EXT_GPL commands
* Segmented DOWNLOAD_MICROCODE
unknown 119[7]
* Gen1 signaling speed (1.5Gb/s)
* Gen2 signaling speed (3.0Gb/s)
* Gen3 signaling speed (6.0Gb/s)
* Native Command Queueing (NCQ)
* Phy event counters
* Idle-Unload when NCQ is active
* NCQ priority information
* READ_LOG_DMA_EXT equivalent to READ_LOG_EXT
* DMA Setup Auto-Activate optimization
* Software settings preservation
* SMART Command Transport (SCT) feature set
* SCT Write Same (AC2)
* SCT Error Recovery Control (AC3)
* SCT Features Control (AC4)
* SCT Data Tables (AC5)
unknown 206[7]
unknown 206[12] (vendor specific)
unknown 206[13] (vendor specific)
* DOWNLOAD MICROCODE DMA command
* WRITE BUFFER DMA command
* READ BUFFER DMA command
Security:
Master password revision code = 65534
supported
not enabled
not locked
not frozen
not expired: security count
supported: enhanced erase
112min for SECURITY ERASE UNIT. 112min for ENHANCED SECURITY ERASE UNIT.
Logical Unit WWN Device Identifier: 50014ee05950af82
NAA : 5
IEEE OUI : 0014ee
Unique ID : 05950af82
Checksum: correct
そして
smartctl -a /dev/sde
出力：
smartctl 6.6 2016-05-31 r4324 [x86_64-linux-4.9.0-3-amd64] (local build)
Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Western Digital Se
Device Model: WDC WD1002F9YZ-09H1JL1
Serial Number: WD-WMC5K0D33MEU
LU WWN Device Id: 5 0014ee 05950af82
Firmware Version: 01.01M03
User Capacity: 1,000,204,886,016 bytes [1.00 TB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Rotation Rate: 7200 rpm
Form Factor: 3.5 inches
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA8-ACS (minor revision not indicated)
SATA Version is: SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is: Mon Oct 2 07:41:14 2017 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: (10560) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 118) minutes.
Conveyance self-test routine
recommended polling time: ( 5) minutes.
SCT capabilities: (0x30bd) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x002f 200 200 051 Pre-fail Always - 0
3 Spin_Up_Time 0x0027 174 171 021 Pre-fail Always - 2291
4 Start_Stop_Count 0x0032 100 100 000 Old_age Always - 202
5 Reallocated_Sector_Ct 0x0033 200 200 140 Pre-fail Always - 0
7 Seek_Error_Rate 0x002e 200 200 000 Old_age Always - 0
9 Power_On_Hours 0x0032 093 093 000 Old_age Always - 5402
10 Spin_Retry_Count 0x0032 100 100 000 Old_age Always - 0
11 Calibration_Retry_Count 0x0032 100 100 000 Old_age Always - 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 202
16 Unknown_Attribute 0x0022 255 000 000 Old_age Always - 8668797885185
183 Runtime_Bad_Block 0x0032 100 100 000 Old_age Always - 0
192 Power-Off_Retract_Count 0x0032 200 200 000 Old_age Always - 65
193 Load_Cycle_Count 0x0032 200 200 000 Old_age Always - 136
194 Temperature_Celsius 0x0022 106 094 000 Old_age Always - 37
196 Reallocated_Event_Count 0x0032 200 200 000 Old_age Always - 0
197 Current_Pending_Sector 0x0032 200 200 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0030 200 200 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x0032 200 200 000 Old_age Always - 20
200 Multi_Zone_Error_Rate 0x0008 200 200 000 Old_age Offline - 0
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
ベストアンサー1
まだ最終段階ではありません。リカバリデバイスを試してみてください--re-add。失敗したすべてのデバイスを自動的に再追加するバリエーションもあります。
mdadm --re-add /dev/md1 faulty
カーネルログは、ドライブが故障とマークされた理由を示します。 SMART状態にUDMA CRCエラーがあるようです。次のコマンドを使用して、ドライブの拡張エラーログを表示することもできます。
smartctl -x /dev/sde
これはエラーの性質を示す必要があります。
Error 10 [9] occurred at disk power-on lifetime: 31192 hours (1299 days + 16 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 00 73 30 a5 58 40 00 Error: UNC at LBA = 0x7330a558 = 1932567896
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
60 05 00 00 e0 00 00 73 30 a1 00 40 08 13d+02:07:12.334 READ FPDMA QUEUED
60 00 08 00 d8 00 00 03 d3 aa c0 40 08 13d+02:07:12.334 READ FPDMA QUEUED
60 05 00 00 d0 00 00 73 30 9c 00 40 08 13d+02:07:12.327 READ FPDMA QUEUED
60 00 08 00 c8 00 00 03 d3 a9 90 40 08 13d+02:07:12.327 READ FPDMA QUEUED
60 05 00 00 c0 00 00 73 30 97 00 40 08 13d+02:07:12.321 READ FPDMA QUEUED
（私のSMARTテストドライブの1つから）。