得た後
WARNING: Your hard drive is failing
Device: /dev/sdb [SAT], 1 Offline uncorrectable sectors
私は走る
$ sudo smartctl -a /dev/sdb
smartctl 6.2 2013-07-26 r3841 [x86_64-linux-3.10.0-514.26.2.el7.x86_64] (local build)
Copyright (C) 2002-13, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Device Model: KingDian S200 60GB
Serial Number: 2017022100551
LU WWN Device Id: 0 000000 000000000
Firmware Version: P0707F1
User Capacity: 60,022,480,896 bytes [60.0 GB]
Sector Size: 512 bytes logical/physical
Rotation Rate: Solid State Device
Device is: Not in smartctl database [for details use: -P showall]
ATA Version is: ACS-2 T13/2015-D revision 3
SATA Version is: SATA >3.1, 6.0 Gb/s (current: 3.0 Gb/s)
Local Time is: Tue Oct 3 10:56:08 2017 BST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 120) seconds.
Offline data collection
capabilities: (0x11) SMART execute Offline immediate.
No Auto Offline data collection support.
Suspend Offline collection upon new
command.
No Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
No Selective Self-test supported.
SMART capabilities: (0x0002) Does not save SMART data before
entering power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 10) minutes.
SMART Attributes Data Structure revision number: 1
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x0032 100 100 050 Old_age Always - 0
5 Reallocated_Sector_Ct 0x0032 100 100 050 Old_age Always - 3
9 Power_On_Hours 0x0032 100 100 050 Old_age Always - 4486
12 Power_Cycle_Count 0x0032 100 100 050 Old_age Always - 13
160 Unknown_Attribute 0x0032 100 100 050 Old_age Always - 1
161 Unknown_Attribute 0x0033 100 100 050 Pre-fail Always - 98
163 Unknown_Attribute 0x0032 100 100 050 Old_age Always - 0
164 Unknown_Attribute 0x0032 100 100 050 Old_age Always - 9724
165 Unknown_Attribute 0x0032 100 100 050 Old_age Always - 9
166 Unknown_Attribute 0x0032 100 100 050 Old_age Always - 1
167 Unknown_Attribute 0x0032 100 100 050 Old_age Always - 5
168 Unknown_Attribute 0x0032 100 100 050 Old_age Always - 1500
169 Unknown_Attribute 0x0032 100 100 050 Old_age Always - 100
175 Program_Fail_Count_Chip 0x0032 100 100 050 Old_age Always - 0
176 Erase_Fail_Count_Chip 0x0032 100 100 050 Old_age Always - 0
177 Wear_Leveling_Count 0x0032 100 100 050 Old_age Always - 9602
178 Used_Rsvd_Blk_Cnt_Chip 0x0032 100 100 050 Old_age Always - 3
181 Program_Fail_Cnt_Total 0x0032 100 100 050 Old_age Always - 0
182 Erase_Fail_Count_Total 0x0032 100 100 050 Old_age Always - 0
192 Power-Off_Retract_Count 0x0032 100 100 050 Old_age Always - 13
194 Temperature_Celsius 0x0022 100 100 050 Old_age Always - 28
195 Hardware_ECC_Recovered 0x0032 100 100 050 Old_age Always - 3994818
196 Reallocated_Event_Count 0x0032 100 100 050 Old_age Always - 2414
197 Current_Pending_Sector 0x0032 100 100 050 Old_age Always - 3
198 Offline_Uncorrectable 0x0032 100 100 050 Old_age Always - 1
199 UDMA_CRC_Error_Count 0x0032 100 100 050 Old_age Always - 0
232 Available_Reservd_Space 0x0032 100 100 050 Old_age Always - 98
241 Total_LBAs_Written 0x0030 100 100 050 Old_age Offline - 36124
242 Total_LBAs_Read 0x0030 100 100 050 Old_age Offline - 10259
245 Unknown_Attribute 0x0032 100 100 050 Old_age Always - 9799
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Extended offline Completed without error 00% 4486 -
Selective Self-tests/Logging not supported
詳細なsmartctl出力は以下を表示します。
$ sudo smartctl -x /dev/sdb
smartctl 6.2 2017-02-27 r4394 [x86_64-linux-3.10.0-514.26.2.el7.x86_64] (local build)
Copyright (C) 2002-13, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Device Model: KingDian S200 60GB
Serial Number: 2017022100551
LU WWN Device Id: 0 000000 000000000
Firmware Version: P0707F1
User Capacity: 60,022,480,896 bytes [60.0 GB]
Sector Size: 512 bytes logical/physical
Rotation Rate: Solid State Device
Device is: Not in smartctl database [for details use: -P showall]
ATA Version is: ACS-2 T13/2015-D revision 3
SATA Version is: SATA >3.1, 6.0 Gb/s (current: 3.0 Gb/s)
Local Time is: Tue Oct 3 15:49:27 2017 BST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
AAM feature is: Unavailable
APM level is: 128 (minimum power consumption without standby)
Rd look-ahead is: Enabled
Write cache is: Enabled
ATA Security is: Disabled, frozen [SEC2]
Wt Cache Reorder: Unavailable
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 120) seconds.
Offline data collection
capabilities: (0x11) SMART execute Offline immediate.
No Auto Offline data collection support.
Suspend Offline collection upon new
command.
No Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
No Selective Self-test supported.
SMART capabilities: (0x0002) Does not save SMART data before
entering power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 10) minutes.
SMART Attributes Data Structure revision number: 1
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE
1 Raw_Read_Error_Rate -O--CK 100 100 050 - 0
5 Reallocated_Sector_Ct -O--CK 100 100 050 - 3
9 Power_On_Hours -O--CK 100 100 050 - 4491
12 Power_Cycle_Count -O--CK 100 100 050 - 13
160 Unknown_Attribute -O--CK 100 100 050 - 1
161 Unknown_Attribute PO--CK 100 100 050 - 98
163 Unknown_Attribute -O--CK 100 100 050 - 0
164 Unknown_Attribute -O--CK 100 100 050 - 10068
165 Unknown_Attribute -O--CK 100 100 050 - 9
166 Unknown_Attribute -O--CK 100 100 050 - 1
167 Unknown_Attribute -O--CK 100 100 050 - 5
168 Unknown_Attribute -O--CK 100 100 050 - 1500
169 Unknown_Attribute -O--CK 100 100 050 - 100
175 Program_Fail_Count_Chip -O--CK 100 100 050 - 0
176 Erase_Fail_Count_Chip -O--CK 100 100 050 - 0
177 Wear_Leveling_Count -O--CK 100 100 050 - 9687
178 Used_Rsvd_Blk_Cnt_Chip -O--CK 100 100 050 - 3
181 Program_Fail_Cnt_Total -O--CK 100 100 050 - 0
182 Erase_Fail_Count_Total -O--CK 100 100 050 - 0
192 Power-Off_Retract_Count -O--CK 100 100 050 - 13
194 Temperature_Celsius -O---K 100 100 050 - 28
195 Hardware_ECC_Recovered -O--CK 100 100 050 - 4314392
196 Reallocated_Event_Count -O--CK 100 100 050 - 2667
197 Current_Pending_Sector -O--CK 100 100 050 - 3
198 Offline_Uncorrectable -O--CK 100 100 050 - 1
199 UDMA_CRC_Error_Count -O--CK 100 100 050 - 0
232 Available_Reservd_Space -O--CK 100 100 050 - 98
241 Total_LBAs_Written ----CK 100 100 050 - 36474
242 Total_LBAs_Read ----CK 100 100 050 - 10529
245 Unknown_Attribute -O--CK 100 100 050 - 10146
||||||_ K auto-keep
|||||__ C event count
||||___ R error rate
|||____ S speed/performance
||_____ O updated online
|______ P prefailure warning
General Purpose Log Directory Version 1
SMART Log Directory Version 1 [multi-sector log support]
Address Access R/W Size Description
0x00 GPL,SL R/O 1 Log Directory
0x01 SL R/O 1 Summary SMART error log
0x02 SL R/O 1 Comprehensive SMART error log
0x03 GPL R/O 1 Ext. Comprehensive SMART error log
0x04 GPL,SL R/O 8 Device Statistics log
0x06 SL R/O 1 SMART self-test log
0x07 GPL R/O 1 Extended self-test log
0x10 GPL R/O 1 NCQ Command Error log
0x11 GPL R/O 1 SATA Phy Event Counters
0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log
0x80-0x9f GPL,SL R/W 16 Host vendor specific log
0xde GPL VS 8 Device vendor specific log
SMART Extended Comprehensive Error Log Version: 1 (1 sectors)
No Errors Logged
SMART Extended Self-test Log Version: 1 (1 sectors)
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Extended offline Completed without error 00% 4488 -
# 2 Extended offline Completed without error 00% 4487 -
# 3 Extended offline Completed without error 00% 4486 -
Selective Self-tests/Logging not supported
SCT Commands not supported
Device Statistics (GP Log 0x04)
Page Offset Size Value Description
1 ===== = = == General Statistics (rev 1) ==
1 0x008 4 13 Lifetime Power-On Resets
1 0x010 4 4491 Power-on Hours
1 0x018 6 2390408669 Logical Sectors Written
1 0x020 6 69617191 Number of Write Commands
1 0x028 6 690041929 Logical Sectors Read
1 0x030 6 6959725 Number of Read Commands
7 ===== = = == Solid State Device Statistics (rev 1) ==
7 0x008 1 0 Percentage Used Endurance Indicator
SATA Phy Event Counters (GP Log 0x11)
ID Size Value Description
0x0001 4 0 Command failed due to ICRC error
0x0002 4 0 R_ERR response for data FIS
0x0005 4 1 R_ERR response for non-data FIS
0x000a 4 17 Device-to-host register FISes sent due to a COMRESET
ベストアンサー1
私は過去にこの問題に直面していました。 IIRC、「オフラインで変更できないセクタ」は、ディスクコントローラ（PCのSATA / SCSIコントローラではなくディスク内部のコントローラ）が繰り返しセクタを読み取れず、そのセクタを絶対に使用できないと判断する場合です。
それでは、そのセクタを使用するファイルシステムに対してそのセクタを不良セクタとして宣言する必要がありますか？
習慣。幸いなことに、今日のディスクは、不良セクタを予備セクタプールの良好なセクタに自動的に交換します。したがって、これらの不良セクタをファイルシステムで使用しなくなるようにファイルシステムに宣言する必要はありません。もちろん、プールのサイズは限られており（Available_Reservd_Space sectorsおそらく）、スペアセクタのすべてを使用した後でも、不良セクタは引き続き使用できないため、ファイルシステムで宣言する必要があります。
それでは、すべてが大丈夫で、これは無害なメッセージですか？
まさか。ドライブは不良セクタを何度も読み取ろうとしましたが、毎回失敗して交換を待っていますが、ドライブは自分でこれを行うことはできません（最終的に読み取ることができると期待しています）。セクタが新しいデータで上書きされるまで、「変更できない」状態のままです。あるいは、ドライブが何らかの方法でそれを読み取ることができる場合は、再マップされ、スペアセクタに置き換えられます（出力smartctlではOffline_Uncorrectable1ずつ減少してReallocated_Sector_Ct増加します）。 1）として。
どうですか？
この場合、通常RAID 1アレイ（良好なディスク - >障害のあるディスク）を強制的に再同期し、新しいセクタに正しい内容が含まれるようにします。とにかくfsck、パーティションのバックアップがある場合（そしてそれが必要な場合）、バックアップを実際の内容と比較してください。