RPi4からUbuntu Mateから起動すると、ドライブが正常に動作します。新しいRPi4でBerrybootで使用する前に再フォーマットしました。 BBのインストール中に「削除できません...」というエラーメッセージが表示されましたが、インストールを続行したところ、Raspbianのインストールが成功したようです。ただし、再起動時に一連のエラーメッセージが表示され、提供されたコンソールモードに入ることはできませんでした。ただ繰り返しました。私はそれを削除して再フォーマットし、Raspbianイメージを直接フラッシュすることを検討し、berrybootをあきらめました。しかし、今はManjaro Gnomeデスクトップからアクセスできません。ディスクやGpartedには何も表示されません。しかし、dmesg（下）のログは、システムがその存在を認識し、方法を見つけようとしていることを示すようです。しかし、これは私の理解の限界であり、よりよく知っている人が知っていることを願っています。 SSDがレンガになったり復元する方法がある場合は、お問い合わせください。 （ところでケーブルではないのは確かです！）
[27958.059701] usb usb2-port1: Cannot enable. Maybe the USB cable is bad?
[27962.563005] usb 2-1: Device not responding to setup address.
[27962.773004] usb 2-1: Device not responding to setup address.
[27962.979681] usb 2-1: device not accepting address 97, error -71
[27964.829787] usb 2-1: Device not responding to setup address.
[27965.039755] usb 2-1: Device not responding to setup address.
[27965.246367] usb 2-1: device not accepting address 98, error -71
[27965.246455] usb usb2-port1: attempt power cycle
[27969.619815] usb usb2-port1: Cannot enable. Maybe the USB cable is bad?
[27977.136538] usb usb2-port1: Cannot enable. Maybe the USB cable is bad?
[27981.309911] usb usb2-port1: Cannot enable. Maybe the USB cable is bad?
[27985.349948] usb usb2-port1: Cannot enable. Maybe the USB cable is bad?
[27992.173343] usb usb2-port1: Cannot enable. Maybe the USB cable is bad?
[27992.733351] usb 2-1: new SuperSpeed Gen 1 USB device number 100 using xhci_hcd
[27992.750695] usb 2-1: New USB device found, idVendor=152d, idProduct=0562, bcdDevice= 2.04
[27992.750701] usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[27992.750705] usb 2-1: Product: USB3.1 TO NVME SSD
[27992.750708] usb 2-1: Manufacturer: Liangteng
[27992.750711] usb 2-1: SerialNumber: DD20180910888
[27992.755322] scsi host13: uas
[27992.755602] scsi 13:0:0:0: Direct-Access ITHOO Tech 0204 PQ: 0 ANSI: 6
[27992.756009] sd 13:0:0:0: Attached scsi generic sg2 type 0
[27994.536635] usb 2-1: USB disconnect, device number 100
[27994.536829] sd 13:0:0:0: tag#5 uas_zap_pending 0 uas-tag 1 inflight: CMD
[27994.536836] sd 13:0:0:0: tag#5 CDB: Test Unit Ready 00 00 00 00 00 00
[27994.740047] sd 13:0:0:0: [sdb] Read Capacity(16) failed: Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK
[27994.740053] sd 13:0:0:0: [sdb] Sense not available.
[27994.940027] sd 13:0:0:0: [sdb] Read Capacity(10) failed: Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK
[27994.940035] sd 13:0:0:0: [sdb] Sense not available.
[27995.020071] sd 13:0:0:0: [sdb] 0 512-byte logical blocks: (0 B/0 B)
[27995.020076] sd 13:0:0:0: [sdb] 0-byte physical blocks
[27995.086718] sd 13:0:0:0: [sdb] Write Protect is off
[27995.086724] sd 13:0:0:0: [sdb] Mode Sense: 00 00 00 00
[27995.153389] sd 13:0:0:0: [sdb] Asking for cache data failed
[27995.153395] sd 13:0:0:0: [sdb] Assuming drive cache: write through
[27995.583395] sd 13:0:0:0: [sdb] Read Capacity(16) failed: Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK
[27995.583400] sd 13:0:0:0: [sdb] Sense not available.
[27995.783396] sd 13:0:0:0: [sdb] Read Capacity(10) failed: Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK
[27995.783402] sd 13:0:0:0: [sdb] Sense not available.
[27996.116733] sd 13:0:0:0: [sdb] Attached SCSI disk
[28000.403421] usb usb2-port1: Cannot enable. Maybe the USB cable is bad?
[28004.446787] usb usb2-port1: Cannot enable. Maybe the USB cable is bad?
[28008.620161] usb usb2-port1: Cannot enable. Maybe the USB cable is bad?
[28012.660199] usb usb2-port1: Cannot enable. Maybe the USB cable is bad?
[28016.833566] usb usb2-port1: Cannot enable. Maybe the USB cable is bad?
[28022.540260] usb usb2-port1: Cannot enable. Maybe the USB cable is bad?
[28029.777038] usb usb2-port1: Cannot enable. Maybe the USB cable is bad?
[28039.027104] usb usb2-port1: Cannot enable. Maybe the USB cable is bad?
[28045.670502] usb usb2-port1: Cannot enable. Maybe the USB cable is bad?
[28050.317265] usb usb2-port1: Cannot enable. Maybe the USB cable is bad?
[28054.357241] usb usb2-port1: Cannot enable. Maybe the USB cable is bad?
[28055.913914] usb 2-1: new SuperSpeed Gen 1 USB device number 101 using xhci_hcd
[28061.057336] usb 2-1: New USB device found, idVendor=152d, idProduct=0562, bcdDevice= 2.04
[28061.057342] usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[28061.227242] usb 2-1: USB disconnect, device number 101
[28065.570677] usb usb2-port1: Cannot enable. Maybe the USB cable is bad?
[28069.744041] usb usb2-port1: Cannot enable. Maybe the USB cable is bad?
[28077.630789] usb usb2-port1: Cannot enable. Maybe the USB cable is bad?
[28081.804158] usb usb2-port1: Cannot enable. Maybe the USB cable is bad?
[28085.844197] usb usb2-port1: Cannot enable. Maybe the USB cable is bad?
[28090.017597] usb usb2-port1: Cannot enable. Maybe the USB cable is bad?
[28094.057605] usb usb2-port1: Cannot enable. Maybe the USB cable is bad?
[28098.230975] usb usb2-port1: Cannot enable. Maybe the USB cable is bad?
[28102.271013] usb usb2-port1: Cannot enable. Maybe the USB cable is bad?
[28112.761109] usb usb2-port1: Cannot enable. Maybe the USB cable is bad?
[28117.407815] usb usb2-port1: Cannot enable. Maybe the USB cable is bad?
[28121.751190] usb usb2-port1: Cannot enable. Maybe the USB cable is bad?
[28131.897945] usb usb2-port1: Cannot enable. Maybe the USB cable is bad?
[28135.937988] usb usb2-port1: Cannot enable. Maybe the USB cable is bad?
[28142.054706] usb usb2-port1: Cannot enable. Maybe the USB cable is bad?
[28146.768079] usb usb2-port1: Cannot enable. Maybe the USB cable is bad?
[28154.911501] usb usb2-port1: Cannot enable. Maybe the USB cable is bad?
[28158.951530] usb usb2-port1: Cannot enable. Maybe the USB cable is bad?
[28163.464900] usb usb2-port1: Cannot enable. Maybe the USB cable is bad?
[28165.848241] usb 2-1: new SuperSpeed Gen 1 USB device number 103 using xhci_hcd
[28165.865580] usb 2-1: New USB device found, idVendor=152d, idProduct=0562, bcdDevice= 2.04
[28165.865586] usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[28165.865590] usb 2-1: Product: USB3.1 TO NVME SSD
[28165.865593] usb 2-1: Manufacturer: Liangteng
[28165.865596] usb 2-1: SerialNumber: DD20180910888
[28165.870697] scsi host13: uas
[28165.871387] scsi 13:0:0:0: Direct-Access ITHOO Tech 0204 PQ: 0 ANSI: 6
[28165.872223] sd 13:0:0:0: Attached scsi generic sg2 type 0
[28165.873122] sd 13:0:0:0: [sdb] 250069680 512-byte logical blocks: (128 GB/119 GiB)
[28165.873128] sd 13:0:0:0: [sdb] 4096-byte physical blocks
[28165.873268] sd 13:0:0:0: [sdb] Write Protect is off
[28165.873272] sd 13:0:0:0: [sdb] Mode Sense: 5f 00 00 08
[28165.873515] sd 13:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[28165.873756] sd 13:0:0:0: [sdb] Optimal transfer size 33553920 bytes not a multiple of physical block size (4096 bytes)
[28166.068149] usb 2-1: USB disconnect, device number 103
[28166.068323] usb 2-1: cmd cmplt err -108
[28166.068331] xhci_hcd 0000:00:14.0: WARN Set TR Deq Ptr cmd failed due to incorrect slot or ep state.
[28166.068391] sd 13:0:0:0: tag#4 uas_zap_pending 0 uas-tag 1 inflight: CMD
[28166.068396] sd 13:0:0:0: tag#4 CDB: Test Unit Ready 00 00 00 00 00 00
[28166.268276] sd 13:0:0:0: [sdb] Read Capacity(16) failed: Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK
[28166.268281] sd 13:0:0:0: [sdb] Sense not available.
[28166.468254] sd 13:0:0:0: [sdb] Read Capacity(10) failed: Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK
[28166.468259] sd 13:0:0:0: [sdb] Sense not available.
[28166.554956] sd 13:0:0:0: [sdb] 0 512-byte logical blocks: (0 B/0 B)
[28166.554962] sd 13:0:0:0: [sdb] 4096-byte physical blocks
[28166.728277] sdb: detected capacity change from 128035676160 to 0
[28166.994947] sd 13:0:0:0: [sdb] Read Capacity(16) failed: Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK
[28166.994952] sd 13:0:0:0: [sdb] Sense not available.
[28167.201616] sd 13:0:0:0: [sdb] Read Capacity(10) failed: Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK
[28167.201622] sd 13:0:0:0: [sdb] Sense not available.
[28167.454955] sd 13:0:0:0: [sdb] Attached SCSI disk
[28175.214997] usb usb2-port1: Cannot enable. Maybe the USB cable is bad?
[28186.798446] usb usb2-port1: Cannot enable. Maybe the USB cable is bad?
[28187.528446] usb 2-1: new SuperSpeed Gen 1 USB device number 104 using xhci_hcd
[28187.545781] usb 2-1: New USB device found, idVendor=152d, idProduct=0562, bcdDevice= 2.04
[28187.545789] usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[28187.545794] usb 2-1: Product: USB3.1 TO NVME SSD
[28187.545798] usb 2-1: Manufacturer: Liangteng
[28187.545803] usb 2-1: SerialNumber: DD20180910888
[28187.551139] scsi host13: uas
[28187.551951] scsi 13:0:0:0: Direct-Access ITHOO Tech 0204 PQ: 0 ANSI: 6
[28187.552706] sd 13:0:0:0: Attached scsi generic sg2 type 0
[28187.553606] sd 13:0:0:0: [sdb] 250069680 512-byte logical blocks: (128 GB/119 GiB)
[28187.553612] sd 13:0:0:0: [sdb] 4096-byte physical blocks
[28187.553751] sd 13:0:0:0: [sdb] Write Protect is off
[28187.553756] sd 13:0:0:0: [sdb] Mode Sense: 5f 00 00 08
[28187.553960] sd 13:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[28187.554163] sd 13:0:0:0: [sdb] Optimal transfer size 33553920 bytes not a multiple of physical block size (4096 bytes)
[28189.415076] usb 2-1: USB disconnect, device number 104
[28189.415246] usb 2-1: cmd cmplt err -108
[28189.415254] xhci_hcd 0000:00:14.0: WARN Set TR Deq Ptr cmd failed due to incorrect slot or ep state.
[28189.415333] sd 13:0:0:0: tag#3 uas_zap_pending 0 uas-tag 1 inflight: CMD
[28189.415338] sd 13:0:0:0: tag#3 CDB: Test Unit Ready 00 00 00 00 00 00
[28189.615153] sd 13:0:0:0: [sdb] Read Capacity(16) failed: Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK
[28189.615159] sd 13:0:0:0: [sdb] Sense not available.
[28189.815156] sd 13:0:0:0: [sdb] Read Capacity(10) failed: Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK
[28189.815162] sd 13:0:0:0: [sdb] Sense not available.
[28189.898477] sd 13:0:0:0: [sdb] 0 512-byte logical blocks: (0 B/0 B)
[28189.898481] sd 13:0:0:0: [sdb] 4096-byte physical blocks
[28190.071820] sdb: detected capacity change from 128035676160 to 0
[28190.338477] sd 13:0:0:0: [sdb] Read Capacity(16) failed: Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK
[28190.338483] sd 13:0:0:0: [sdb] Sense not available.
[28190.538500] sd 13:0:0:0: [sdb] Read Capacity(10) failed: Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK
[28190.538506] sd 13:0:0:0: [sdb] Sense not available.
[28190.791840] sd 13:0:0:0: [sdb] Attached SCSI disk
[28199.471894] usb usb2-port1: Cannot enable. Maybe the USB cable is bad?
[28204.665275] usb usb2-port1: Cannot enable. Maybe the USB cable is bad?
[28209.008647] usb usb2-port1: Cannot enable. Maybe the USB cable is bad?
[28212.048663] usb 2-1: new SuperSpeed Gen 1 USB device number 105 using xhci_hcd
[28212.066008] usb 2-1: New USB device found, idVendor=152d, idProduct=0562, bcdDevice= 2.04
[28212.066017] usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[28212.066023] usb 2-1: Product: USB3.1 TO NVME SSD
[28212.066028] usb 2-1: Manufacturer: Liangteng
[28212.066032] usb 2-1: SerialNumber: DD20180910888
[28212.071230] scsi host13: uas
[28212.071903] scsi 13:0:0:0: Direct-Access ITHOO Tech 0204 PQ: 0 ANSI: 6
[28212.072654] sd 13:0:0:0: Attached scsi generic sg2 type 0
[28212.073388] sd 13:0:0:0: [sdb] 250069680 512-byte logical blocks: (128 GB/119 GiB)
[28212.073394] sd 13:0:0:0: [sdb] 4096-byte physical blocks
[28212.073520] sd 13:0:0:0: [sdb] Write Protect is off
[28212.073525] sd 13:0:0:0: [sdb] Mode Sense: 5f 00 00 08
[28212.073729] sd 13:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[28212.073931] sd 13:0:0:0: [sdb] Optimal transfer size 33553920 bytes not a multiple of physical block size (4096 bytes)
[28216.688717] usb usb2-port1: Cannot enable. Maybe the USB cable is bad?
[28216.688738] usb 2-1: USB disconnect, device number 105
[28216.688988] sd 13:0:0:0: [sdb] tag#23 uas_zap_pending 0 uas-tag 1 inflight: CMD
[28216.688994] sd 13:0:0:0: [sdb] tag#23 CDB: Read(10) 28 00 00 00 00 00 00 00 08 00
[28216.689046] sd 13:0:0:0: [sdb] tag#23 FAILED Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK
[28216.689051] sd 13:0:0:0: [sdb] tag#23 CDB: Read(10) 28 00 00 00 00 00 00 00 08 00
[28216.689054] print_req_error: 18 callbacks suppressed
[28216.689059] blk_update_request: I/O error, dev sdb, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0
[28216.689064] buffer_io_error: 1 callbacks suppressed
[28216.689066] Buffer I/O error on dev sdb, logical block 0, async page read
[28216.689183] blk_update_request: I/O error, dev sdb, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0
[28216.689189] Buffer I/O error on dev sdb, logical block 0, async page read
[28216.689202] ldm_validate_partition_table(): Disk read failed.
[28216.689219] blk_update_request: I/O error, dev sdb, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0
[28216.689223] Buffer I/O error on dev sdb, logical block 0, async page read
[28216.689240] blk_update_request: I/O error, dev sdb, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0
[28216.689243] Buffer I/O error on dev sdb, logical block 0, async page read
[28216.689260] blk_update_request: I/O error, dev sdb, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0
[28216.689263] Buffer I/O error on dev sdb, logical block 0, async page read
[28216.689269] sdb: unable to read partition table
[28216.955426] sd 13:0:0:0: [sdb] Read Capacity(16) failed: Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK
[28216.955432] sd 13:0:0:0: [sdb] Sense not available.
[28217.155407] sd 13:0:0:0: [sdb] Read Capacity(10) failed: Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK
[28217.155412] sd 13:0:0:0: [sdb] Sense not available.
[28217.235418] sd 13:0:0:0: [sdb] 0 512-byte logical blocks: (0 B/0 B)
[28217.235423] sd 13:0:0:0: [sdb] 4096-byte physical blocks
[28217.408746] sd 13:0:0:0: [sdb] Attached SCSI disk
[28223.502118] usb usb2-port1: Cannot enable. Maybe the USB cable is bad?
[28232.452185] usb usb2-port1: Cannot enable. Maybe the USB cable is bad?
[28236.795550] usb usb2-port1: Cannot enable. Maybe the USB cable is bad?
[28240.835596] usb usb2-port1: Cannot enable. Maybe the USB cable is bad?
[28246.818991] usb usb2-port1: Cannot enable. Maybe the USB cable is bad?
[28251.329032] usb usb2-port1: Cannot enable. Maybe the USB cable is bad?
[28258.342429] usb usb2-port1: Cannot enable. Maybe the USB cable is bad?
[28265.469159] usb usb2-port1: Cannot enable. Maybe the USB cable is bad?
[28271.999228] usb usb2-port1: Cannot enable. Maybe the USB cable is bad?
[28282.249310] usb usb2-port1: Cannot enable. Maybe the USB cable is bad?
[28295.102764] usb usb2-port1: Cannot enable. Maybe the USB cable is bad?
[28297.522962] usb 2-1: Device not responding to setup address.
[28297.732737] usb 2-1: Device not responding to setup address.
[28297.939416] usb 2-1: device not accepting address 106, error -71
[28298.959461] usb 2-1: Device not responding to setup address.
[28299.169465] usb 2-1: Device not responding to setup address.
[28299.376069] usb 2-1: device not accepting address 107, error -71
[28299.376158] usb usb2-port1: attempt power cycle
[28301.392758] usb 1-1: new high-speed USB device number 66 using xhci_hcd
[28309.569560] usb usb2-port1: Cannot enable. Maybe the USB cable is bad?
[28313.609589] usb usb2-port1: Cannot enable. Maybe the USB cable is bad?
[28328.603066] usb usb2-port1: Cannot enable. Maybe the USB cable is bad?
[28336.559807] usb usb2-port1: Cannot enable. Maybe the USB cable is bad?
[28339.803151] usb 2-1: new SuperSpeed Gen 1 USB device number 109 using xhci_hcd
[28339.820599] usb 2-1: New USB device found, idVendor=152d, idProduct=0562, bcdDevice= 2.04
[28339.820605] usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[28339.820609] usb 2-1: Product: USB3.1 TO NVME SSD
[28339.820612] usb 2-1: Manufacturer: Liangteng
[28339.820615] usb 2-1: SerialNumber: DD20180910888
[28339.828404] scsi host13: uas
[28339.829118] scsi 13:0:0:0: Direct-Access ITHOO Tech 0204 PQ: 0 ANSI: 6
[28339.830171] sd 13:0:0:0: Attached scsi generic sg2 type 0
[28339.830772] sd 13:0:0:0: [sdb] 250069680 512-byte logical blocks: (128 GB/119 GiB)
[28339.830778] sd 13:0:0:0: [sdb] 4096-byte physical blocks
[28339.830910] sd 13:0:0:0: [sdb] Write Protect is off
[28339.830915] sd 13:0:0:0: [sdb] Mode Sense: 5f 00 00 08
[28339.831193] sd 13:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[28339.831534] sd 13:0:0:0: [sdb] Optimal transfer size 33553920 bytes not a multiple of physical block size (4096 bytes)
[28339.865797] sdb: sdb1 sdb2
[28339.866811] sd 13:0:0:0: [sdb] Attached SCSI disk
[28340.049781] usb 2-1: USB disconnect, device number 109
[28340.051647] sd 13:0:0:0: [sdb] Synchronizing SCSI cache
[28340.249809] sd 13:0:0:0: [sdb] Synchronize Cache(10) failed: Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK
[28346.913236] usb usb2-port1: Cannot enable. Maybe the USB cable is bad?
[28351.292797] proc: Bad value for 'hidepid'
[28351.328456] audit: type=1130 audit(1616687832.662:182): pid=1 uid=0 auid=4294967295 ses=4294967295 msg='unit=systemd-hostnamed comm="systemd" exe="/usr/lib/systemd/systemd" hostname=? addr=? terminal=? res=success'
[28355.206641] usb usb2-port1: Cannot enable. Maybe the USB cable is bad?
[28361.540038] usb usb2-port1: Cannot enable. Maybe the USB cable is bad?
[28365.580058] usb usb2-port1: Cannot enable. Maybe the USB cable is bad?
[28369.753445] usb usb2-port1: Cannot enable. Maybe the USB cable is bad?
[28399.906129] audit: type=1131 audit(1616687881.238:183): pid=1 uid=0 auid=4294967295 ses=4294967295 msg='unit=systemd-hostnamed comm="systemd" exe="/usr/lib/systemd/systemd" hostname=? addr=? terminal=? res=success'
[27949.779616] usb usb2-port1: Cannot enable. Maybe the USB cable is bad?
[27958.059701] usb usb2-port1: Cannot enable. Maybe the USB cable is bad?
[27962.563005] usb 2-1: Device not responding to setup address.
[27962.773004] usb 2-1: Device not responding to setup address.
[27962.979681] usb 2-1: device not accepting address 97, error -71
[27964.829787] usb 2-1: Device not responding to setup address.
[27965.039755] usb 2-1: Device not responding to setup address.
[27965.246367] usb 2-1: device not accepting address 98, error -71
[27965.246455] usb usb2-port1: attempt power cycle
[27969.619815] usb usb2-port1: Cannot enable. Maybe the USB cable is bad?
[27977.136538] usb usb2-port1: Cannot enable. Maybe the USB cable is bad?
[27981.309911] usb usb2-port1: Cannot enable. Maybe the USB cable is bad?
[27985.349948] usb usb2-port1: Cannot enable. Maybe the USB cable is bad?
[27992.173343] usb usb2-port1: Cannot enable. Maybe the USB cable is bad?
[27992.733351] usb 2-1: new SuperSpeed Gen 1 USB device number 100 using xhci_hcd
[27992.750695] usb 2-1: New USB device found, idVendor=152d, idProduct=0562, bcdDevice= 2.04
[27992.750701] usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[27992.750705] usb 2-1: Product: USB3.1 TO NVME SSD
[27992.750708] usb 2-1: Manufacturer: Liangteng
[27992.750711] usb 2-1: SerialNumber: DD20180910888
[27992.755322] scsi host13: uas
[27992.755602] scsi 13:0:0:0: Direct-Access ITHOO Tech 0204 PQ: 0 ANSI: 6
[27992.756009] sd 13:0:0:0: Attached scsi generic sg2 type 0
[27994.536635] usb 2-1: USB disconnect, device number 100
[27994.536829] sd 13:0:0:0: tag#5 uas_zap_pending 0 uas-tag 1 inflight: CMD
[27994.536836] sd 13:0:0:0: tag#5 CDB: Test Unit Ready 00 00 00 00 00 00
[27994.740047] sd 13:0:0:0: [sdb] Read Capacity(16) failed: Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK
[27994.740053] sd 13:0:0:0: [sdb] Sense not available.
[27994.940027] sd 13:0:0:0: [sdb] Read Capacity(10) failed: Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK
[27994.940035] sd 13:0:0:0: [sdb] Sense not available.
[27995.020071] sd 13:0:0:0: [sdb] 0 512-byte logical blocks: (0 B/0 B)
[27995.020076] sd 13:0:0:0: [sdb] 0-byte physical blocks
[27995.086718] sd 13:0:0:0: [sdb] Write Protect is off
[27995.086724] sd 13:0:0:0: [sdb] Mode Sense: 00 00 00 00
[27995.153389] sd 13:0:0:0: [sdb] Asking for cache data failed
[27995.153395] sd 13:0:0:0: [sdb] Assuming drive cache: write through
[27995.583395] sd 13:0:0:0: [sdb] Read Capacity(16) failed: Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK
[27995.583400] sd 13:0:0:0: [sdb] Sense not available.
[27995.783396] sd 13:0:0:0: [sdb] Read Capacity(10) failed: Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK
[27995.783402] sd 13:0:0:0: [sdb] Sense not available.
[27996.116733] sd 13:0:0:0: [sdb] Attached SCSI disk
[28000.403421] usb usb2-port1: Cannot enable. Maybe the USB cable is bad?
[28004.446787] usb usb2-port1: Cannot enable. Maybe the USB cable is bad?
[28008.620161] usb usb2-port1: Cannot enable. Maybe the USB cable is bad?
[28012.660199] usb usb2-port1: Cannot enable. Maybe the USB cable is bad?
[28016.833566] usb usb2-port1: Cannot enable. Maybe the USB cable is bad?
[28022.540260] usb usb2-port1: Cannot enable. Maybe the USB cable is bad?
[28029.777038] usb usb2-port1: Cannot enable. Maybe the USB cable is bad?
[28039.027104] usb usb2-port1: Cannot enable. Maybe the USB cable is bad?
[28045.670502] usb usb2-port1: Cannot enable. Maybe the USB cable is bad?
[28050.317265] usb usb2-port1: Cannot enable. Maybe the USB cable is bad?
[28054.357241] usb usb2-port1: Cannot enable. Maybe the USB cable is bad?
[28055.913914] usb 2-1: new SuperSpeed Gen 1 USB device number 101 using xhci_hcd
[28061.057336] usb 2-1: New USB device found, idVendor=152d, idProduct=0562, bcdDevice= 2.04
[28061.057342] usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[28061.227242] usb 2-1: USB disconnect, device number 101