私は放棄されたコンピュータからインポートされた古いSeagate 4TB内蔵ハードドライブをゲーム用のバックアップハードドライブとしてリサイクルする予定です。
安全のために最初にsmartctlスキャンを実行したかったので、そうしてsmartctl -t short /dev/sdb結果を得ました。 「WHEN_FAILED」列には何も表示されないため、問題はないようです（最初は主に温度関連のエラーに興味がありました）。ところで私は見た。2018年の記事 「Current_Pending_Sector」への言及はかなり深刻です。私のものはゼロではなくエラーもあります...気にする必要があるかどうかわからないので、SEを試してみるかと思いました。 。
これまで私の推測では重要な内容を入れてはいけないということです。しかし、保存フォルダをシンボリックリンクして他の場所に（より良い結果を得るためにドライブに）存在させて、もう一度気にしないと、ゲームで利用できるはずです。ドライブが失敗した場合は、インストールされたゲームをダウンロードしてください。また、「READ DMA EXT」エラーが差し迫ったエラーを示すのか、ケーブルやその他のワンタイムイベントであるのかはわかりません（エラー35-39のみが表示され、すべて「16936時間」に発生します...いいえ。すべてのエラー表示できる方法があるかどうか、または表示されているように最後の5つのエラーのみを保存することを確認してください。あるだけです）。
ドライブに寿命が少しでも残っている可能性が少しでもあれば、それほど重要ではないものに変えても大丈夫です。しかし、近い将来に失敗する可能性が高く、新しい磁石を購入する以外に時間を無駄にしたくありません。 :-) どのような提案/推奨事項がありますか？
とにかくまた走り、smartctl -t long /dev/sdb翌日まで待ったsmartctl -a /dev/sdb。結果は次のとおりです。
I_AM_ROOT@fedora35:~
# smartctl -a /dev/sdb
smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.15.7-200.fc35.x86_64] (local build)
Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Seagate Desktop HDD.15
Device Model: ST4000DM000-1F2168
Serial Number: <Redacted>
LU WWN Device Id: <Redacted>
Firmware Version: CC54
User Capacity: 4,000,787,030,016 bytes [4.00 TB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Rotation Rate: 5900 rpm
Form Factor: 3.5 inches
Device is: In smartctl database [for details use: -P show]
ATA Version is: ACS-2, ACS-3 T13/2161-D revision 3b
SATA Version is: SATA 3.1, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is: Fri Dec 17 11:44:49 2021 EST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 118) The previous self-test completed having
the read element of the test failed.
Total time to complete Offline
data collection: ( 168) seconds.
Offline data collection
capabilities: (0x73) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
No Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 528) minutes.
Conveyance self-test routine
recommended polling time: ( 2) minutes.
SCT capabilities: (0x1085) SCT Status supported.
SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 119 099 006 Pre-fail Always - 233492808
3 Spin_Up_Time 0x0003 092 091 000 Pre-fail Always - 0
4 Start_Stop_Count 0x0032 099 099 020 Old_age Always - 1890
5 Reallocated_Sector_Ct 0x0033 100 100 010 Pre-fail Always - 0
7 Seek_Error_Rate 0x000f 044 039 030 Pre-fail Always - 678608011490
9 Power_On_Hours 0x0032 065 065 000 Old_age Always - 30836
10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 099 099 020 Old_age Always - 1206
183 Runtime_Bad_Block 0x0032 100 100 000 Old_age Always - 0
184 End-to-End_Error 0x0032 100 100 099 Old_age Always - 0
187 Reported_Uncorrect 0x0032 061 061 000 Old_age Always - 39
188 Command_Timeout 0x0032 100 100 000 Old_age Always - 0 0 0
189 High_Fly_Writes 0x003a 100 100 000 Old_age Always - 0
190 Airflow_Temperature_Cel 0x0022 071 058 045 Old_age Always - 29 (Min/Max 27/32)
191 G-Sense_Error_Rate 0x0032 100 100 000 Old_age Always - 0
192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 304
193 Load_Cycle_Count 0x0032 084 084 000 Old_age Always - 32204
194 Temperature_Celsius 0x0022 029 042 000 Old_age Always - 29 (0 12 0 0 0)
197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 16
198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 16
199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0
240 Head_Flying_Hours 0x0000 100 253 000 Old_age Offline - 23293h+16m+41.533s
241 Total_LBAs_Written 0x0000 100 253 000 Old_age Offline - 19236444339
242 Total_LBAs_Read 0x0000 100 253 000 Old_age Offline - 27220280383
SMART Error Log Version: 1
ATA Error Count: 39 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 39 occurred at disk power-on lifetime: 16936 hours (705 days + 16 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 08 ff ff ff ef 00 04:59:22.764 READ DMA EXT
25 00 40 ff ff ff ef 00 04:59:22.762 READ DMA EXT
25 00 00 ff ff ff ef 00 04:59:22.736 READ DMA EXT
25 00 08 ff ff ff ef 00 04:59:22.735 READ DMA EXT
ef 10 02 00 00 00 a0 00 04:59:22.735 SET FEATURES [Enable SATA feature]
Error 38 occurred at disk power-on lifetime: 16936 hours (705 days + 16 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 08 ff ff ff ef 00 04:59:18.709 READ DMA EXT
25 00 00 ff ff ff ef 00 04:59:18.696 READ DMA EXT
25 00 00 ff ff ff ef 00 04:59:18.693 READ DMA EXT
25 00 00 ff ff ff ef 00 04:59:18.631 READ DMA EXT
25 00 08 ff ff ff ef 00 04:59:18.631 READ DMA EXT
Error 37 occurred at disk power-on lifetime: 16936 hours (705 days + 16 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 08 ff ff ff ef 00 04:57:53.914 READ DMA EXT
25 00 08 ff ff ff ef 00 04:57:53.914 READ DMA EXT
25 00 00 ff ff ff ef 00 04:57:53.882 READ DMA EXT
ef 10 02 00 00 00 a0 00 04:57:53.881 SET FEATURES [Enable SATA feature]
27 00 00 00 00 00 e0 00 04:57:53.881 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
Error 36 occurred at disk power-on lifetime: 16936 hours (705 days + 16 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 08 ff ff ff ef 00 04:57:49.903 READ DMA EXT
25 00 08 ff ff ff ef 00 04:57:49.903 READ DMA EXT
25 00 08 ff ff ff ef 00 04:57:49.903 READ DMA EXT
25 00 08 ff ff ff ef 00 04:57:49.903 READ DMA EXT
25 00 08 ff ff ff ef 00 04:57:49.903 READ DMA EXT
Error 35 occurred at disk power-on lifetime: 16936 hours (705 days + 16 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 00 ff ff ff ef 00 04:57:45.210 READ DMA EXT
25 00 00 ff ff ff ef 00 04:57:45.181 READ DMA EXT
25 00 00 ff ff ff ef 00 04:57:45.179 READ DMA EXT
25 00 00 ff ff ff ef 00 04:57:45.178 READ DMA EXT
25 00 58 ff ff ff ef 00 04:57:45.149 READ DMA EXT
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Extended offline Completed: read failure 60% 30817 3723785408
# 2 Short offline Completed without error 00% 30812 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
ベストアンサー1
SMARTも悪くはありませんが、HDDファームウェアで解決できないいくつかのエラーがあります。
これで、どのセクタが破損しているかを正確に知っているので、ddを使用してそのセクタを再割り当てしてみることができます。
https://www.smartmontools.org/wiki/BadBlockHowto
ただし、ドライブは現在安全に使用できないため、修理しても失われる可能性がある重要でない情報を保存するためにのみ使用することをお勧めします。