ルーメンセンサーを正しく出力できない、またはATI Radeonの温度とファンをロードできません。

私はLinuxに初めて触れ、いくつかの小さな問題があります。フォローするこのガイド最初は正しい出力が受信されず、ATI Radeon HD 5000の温度またはファン速度は表示されません。それから私はこのガイド、そして同じ問題が発生しました。インストール中に問題は発生せず、エラーも発生しませんでした。i2c何らかの理由で読むことができないと思います。専用ドライバがインストールされ、正しく動作しますfglrxinfo。コマンドを使用aticonfigして温度とファンを表示できます。どんなアイデアがありますか？

どのように動作させるかについてのアイデアはありますかsensors？

これは私が実行したときのsudo sensors-detect結果です。

# sensors-detect revision 5984 (2011-07-10 21:22:53 +0200)
# System: LENOVO IdeaPad Y560 (laptop)
# Board: Lenovo KL3

This program will help you determine which kernel modules you need
to load to use lm_sensors most effectively. It is generally safe
and recommended to accept the default answers to all questions,
unless you know what you're doing.

Some south bridges, CPUs or memory controllers contain embedded sensors.
Do you want to scan for them? This is totally safe. (YES/no): y
Silicon Integrated Systems SIS5595...                       No
VIA VT82C686 Integrated Sensors...                          No
VIA VT8231 Integrated Sensors...                            No
AMD K8 thermal sensors...                                   No
AMD Family 10h thermal sensors...                           No
AMD Family 11h thermal sensors...                           No
AMD Family 12h and 14h thermal sensors...                   No
AMD Family 15h thermal sensors...                           No
AMD Family 15h power sensors...                             No
Intel digital thermal sensor...                             Success!
    (driver `coretemp')
Intel AMB FB-DIMM thermal sensor...                         No
VIA C7 thermal sensor...                                    No
VIA Nano thermal sensor...                                  No

Some Super I/O chips contain embedded sensors. We have to write to
standard I/O ports to probe them. This is usually safe.
Do you want to scan for Super I/O sensors? (YES/no): y
Probing for Super-I/O at 0x2e/0x2f
Trying family `National Semiconductor/ITE'...               Yes
Found unknown chip with ID 0x8502
Probing for Super-I/O at 0x4e/0x4f
Trying family `National Semiconductor/ITE'...               No
Trying family `SMSC'...                                     No
Trying family `VIA/Winbond/Nuvoton/Fintek'...               No
Trying family `ITE'...                                      No

Some hardware monitoring chips are accessible through the ISA I/O ports.
We have to write to arbitrary I/O ports to probe them. This is usually
safe though. Yes, you do have ISA I/O ports even if you do not have any
ISA slots! Do you want to scan the ISA I/O ports? (YES/no): y
Probing for `National Semiconductor LM78' at 0x290...       No
Probing for `National Semiconductor LM79' at 0x290...       No
Probing for `Winbond W83781D' at 0x290...                   No
Probing for `Winbond W83782D' at 0x290...                   No

Lastly, we can probe the I2C/SMBus adapters for connected hardware
monitoring devices. This is the most risky part, and while it works
reasonably well on most systems, it has been reported to cause trouble
on some systems.
Do you want to probe the I2C/SMBus adapters now? (YES/no): y
Using driver `i2c-i801' for device 0000:00:1f.3: Intel 3400/5 Series (PCH)

Now follows a summary of the probes I have just done.
Just press ENTER to continue: 

Driver `coretemp':
  * Chip `Intel digital thermal sensor' (confidence: 9)

To load everything that is needed, add this to /etc/modules:
#----cut here----
# Chip drivers
coretemp
#----cut here----
If you have some drivers built into your kernel, the list above will
contain too many modules. Skip the appropriate ones!

Do you want to add these lines automatically to /etc/modules? (yes/NO)

私の結果sensorsは次のとおりです

acpitz-virtual-0
Adapter: Virtual device
temp1:        +58.0°C  (crit = +100.0°C)

coretemp-isa-0000
Adapter: ISA adapter
Core 0:       +56.0°C  (high = +84.0°C, crit = +100.0°C)
Core 1:       +57.0°C  (high = +84.0°C, crit = +100.0°C)
Core 2:       +58.0°C  (high = +84.0°C, crit = +100.0°C)
Core 3:       +57.0°C  (high = +84.0°C, crit = +100.0°C)

私/etc/modulesのもの：

# /etc/modules: kernel modules to load at boot time.
#
# This file contains the names of kernel modules that should be loaded
# at boot time, one per line. Lines beginning with "#" are ignored.

lp
rtc

# Generated by sensors-detect on Fri Nov 30 23:24:31 2012
# Chip drivers
coretemp