昨夜、Ubuntuサーバーのシステムクロックが5分進んでいることを発見し、 "ntpdate pool.ntp.org"コマンドを実行して寝ました。
今朝私はSAMBA株が働かないことを発見しました。サーバーを見ると、権限が?に設定されていることがわかります。 ？ ？当該株式が所在する所の取引量です。
サーバーを再起動しましたが、mdadmが失敗したことがわかります。
[ 13.920349] sd 3:0:0:0: [sdb]
[ 13.920388] Sense Key : Medium Error [current] [descriptor]
[ 13.920499] Descriptor sense data with sense descriptors (in hex):
[ 13.920559] 72 03 11 04 00 00 00 0c 00 0a 80 00 00 00 00 00
[ 13.922059] 00 00 00 00
[ 13.922223] sd 3:0:0:0: [sdb]
[ 13.922255] Add. Sense: Unrecovered read error - auto reallocate failed
[ 13.922316] sd 3:0:0:0: [sdb] CDB:
[ 13.922347] Read(16): 88 00 00 00 00 00 00 00 00 00 00 00 00 08 00 00
[ 13.922855] end_request: I/O error, dev sdb, sector 0
[ 13.922888] Buffer I/O error on device sdb, logical block 0
[ 13.922927] ata4: EH complete
[ 14.859145] ldm_validate_partition_table(): Disk read failed.
[ 14.859203] Dev sdb: unable to read RDB block 0
[ 14.870317] sdb: unable to read partition table
[ 14.870646] sdb: detected capacity change from 0 to 4000787030016
[ 14.870869] sd 3:0:0:0: [sdb] Attached SCSI disk
[ 14.886265] random: nonblocking pool is initialized
[ 15.510741] md: bind<sdc1>
だからここでこの問題を解決したいのはmdadm.confです。
cat /etc/mdadm/mdadm.conf
# mdadm.conf
#
# Please refer to mdadm.conf(5) for information about this file.
#
# by default (built-in), scan all partitions (/proc/partitions) and all
# containers for MD superblocks. alternatively, specify devices to scan, using
# wildcards if desired.
#DEVICE partitions containers
# auto-create devices with Debian standard permissions
CREATE owner=root group=disk mode=0660 auto=yes
# automatically tag new arrays as belonging to the local system
HOMEHOST <system>
# instruct the monitoring daemon where to send mail alerts
MAILADDR root
# definitions of existing MD arrays
# This file was auto-generated on Mon, 16 Feb 2015 18:24:04 -0500
# by mkconf $Id$
DEVICE /dev/sdb1 /dev/sdc1
ARRAY /dev/md0 level=raid0 devices=/dev/sdb1,/dev/sdc1
次に、RAIDの両方のディスクでsmartctlコマンドを実行しましたが、どちらも正常に見えました。
smartctl -a -s on /dev/sdb
smartctl 6.2 2013-07-26 r3841 [x86_64-linux-3.13.0-45-generic] (local build)
Copyright (C) 2002-13, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Device Model: WDC WD40EZRX-00SPEB0
Serial Number: WD-WCC4E0NLZ6ED
LU WWN Device Id: 5 0014ee 20b74560f
Firmware Version: 80.00A80
User Capacity: 4,000,787,030,016 bytes [4.00 TB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Rotation Rate: 5400 rpm
Device is: Not in smartctl database [for details use: -P showall]
ATA Version is: ACS-2 (minor revision not indicated)
SATA Version is: SATA 3.0, 6.0 Gb/s (current: 3.0 Gb/s)
Local Time is: Fri Oct 2 11:45:31 2015 EDT
SMART support is: Available - device has SMART capability.
SMART support is: Disabled
=== START OF ENABLE/DISABLE COMMANDS SECTION ===
SMART Enabled.
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: (55740) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 557) minutes.
Conveyance self-test routine
recommended polling time: ( 5) minutes.
SCT capabilities: (0x7035) SCT Status supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x002f 100 253 051 Pre-fail Always - 0
3 Spin_Up_Time 0x0027 184 184 021 Pre-fail Always - 7775
4 Start_Stop_Count 0x0032 100 100 000 Old_age Always - 15
5 Reallocated_Sector_Ct 0x0033 200 200 140 Pre-fail Always - 0
7 Seek_Error_Rate 0x002e 200 200 000 Old_age Always - 0
9 Power_On_Hours 0x0032 093 093 000 Old_age Always - 5434
10 Spin_Retry_Count 0x0032 100 253 000 Old_age Always - 0
11 Calibration_Retry_Count 0x0032 100 253 000 Old_age Always - 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 15
192 Power-Off_Retract_Count 0x0032 200 200 000 Old_age Always - 6
193 Load_Cycle_Count 0x0032 132 132 000 Old_age Always - 204074
194 Temperature_Celsius 0x0022 119 109 000 Old_age Always - 33
196 Reallocated_Event_Count 0x0032 200 200 000 Old_age Always - 0
197 Current_Pending_Sector 0x0032 200 200 000 Old_age Always - 96
198 Offline_Uncorrectable 0x0030 200 200 000 Old_age Offline - 49
199 UDMA_CRC_Error_Count 0x0032 200 200 000 Old_age Always - 0
200 Multi_Zone_Error_Rate 0x0008 199 199 000 Old_age Offline - 758
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
smartctl -a -s on /dev/sdc
smartctl 6.2 2013-07-26 r3841 [x86_64-linux-3.13.0-45-generic] (local build)
Copyright (C) 2002-13, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Device Model: WDC WD40EZRX-00SPEB0
Serial Number: WD-WCC4E0CZDE98
LU WWN Device Id: 5 0014ee 2b6205b40
Firmware Version: 80.00A80
User Capacity: 4,000,787,030,016 bytes [4.00 TB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Rotation Rate: 5400 rpm
Device is: Not in smartctl database [for details use: -P showall]
ATA Version is: ACS-2 (minor revision not indicated)
SATA Version is: SATA 3.0, 6.0 Gb/s (current: 3.0 Gb/s)
Local Time is: Fri Oct 2 11:47:29 2015 EDT
SMART support is: Available - device has SMART capability.
SMART support is: Disabled
=== START OF ENABLE/DISABLE COMMANDS SECTION ===
SMART Enabled.
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: (52020) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 520) minutes.
Conveyance self-test routine
recommended polling time: ( 5) minutes.
SCT capabilities: (0x7035) SCT Status supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x002f 100 253 051 Pre-fail Always - 0
3 Spin_Up_Time 0x0027 174 174 021 Pre-fail Always - 8258
4 Start_Stop_Count 0x0032 100 100 000 Old_age Always - 10
5 Reallocated_Sector_Ct 0x0033 200 200 140 Pre-fail Always - 0
7 Seek_Error_Rate 0x002e 200 200 000 Old_age Always - 0
9 Power_On_Hours 0x0032 093 093 000 Old_age Always - 5434
10 Spin_Retry_Count 0x0032 100 253 000 Old_age Always - 0
11 Calibration_Retry_Count 0x0032 100 253 000 Old_age Always - 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 10
192 Power-Off_Retract_Count 0x0032 200 200 000 Old_age Always - 3
193 Load_Cycle_Count 0x0032 138 138 000 Old_age Always - 188394
194 Temperature_Celsius 0x0022 120 112 000 Old_age Always - 32
196 Reallocated_Event_Count 0x0032 200 200 000 Old_age Always - 0
197 Current_Pending_Sector 0x0032 200 200 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0030 200 200 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x0032 200 200 000 Old_age Always - 0
200 Multi_Zone_Error_Rate 0x0008 200 200 000 Old_age Offline - 0
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
これまでは、すべてが大丈夫に見えますが、mdadmを実行すると、次のような結果が表示されます。
mdadm -E /dev/sdc1
/dev/sdc1:
Magic : a92b4efc
Version : 1.2
Feature Map : 0x0
Array UUID : 933d1825:56122a49:779fbad0:926ab5c9
Name : BAILEYFS01:0 (local to host BAILEYFS01)
Creation Time : Tue Feb 17 17:22:13 2015
Raid Level : raid0
Raid Devices : 2
Avail Dev Size : 7814033392 (3726.02 GiB 4000.79 GB)
Data Offset : 16 sectors
Super Offset : 8 sectors
State : clean
Device UUID : e78061dc:86e60bc0:f4f81839:3816d74a
Update Time : Tue Feb 17 17:22:13 2015
Checksum : 1d8e1dfc - correct
Events : 0
Chunk Size : 512K
Device Role : Active device 1
Array State : AA ('A' == active, '.' == missing)
mdadm -E /dev/sdb1
mdadm: cannot open /dev/sdb1: No such file or directory
これは、アレイの2つのディスクに対するfdiskの出力です。
fdisk -l /dev/sdb
WARNING: GPT (GUID Partition Table) detected on '/dev/sdb'! The util fdisk doesn't support GPT. Use GNU Parted.
Disk /dev/sdb: 4000.8 GB, 4000787030016 bytes
255 heads, 63 sectors/track, 486401 cylinders, total 7814037168 sectors
Units = sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 4096 bytes
I/O size (minimum/optimal): 4096 bytes / 4096 bytes
Disk identifier: 0x00000000
Device Boot Start End Blocks Id System
/dev/sdb1 1 4294967295 2147483647+ ee GPT
Partition 1 does not start on physical sector boundary.
fdisk -l /dev/sdc
WARNING: GPT (GUID Partition Table) detected on '/dev/sdc'! The util fdisk doesn't support GPT. Use GNU Parted.
Disk /dev/sdc: 4000.8 GB, 4000787030016 bytes
255 heads, 63 sectors/track, 486401 cylinders, total 7814037168 sectors
Units = sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 4096 bytes
I/O size (minimum/optimal): 4096 bytes / 4096 bytes
Disk identifier: 0x00000000
Device Boot Start End Blocks Id System
/dev/sdc1 1 4294967295 2147483647+ ee GPT
Partition 1 does not start on physical sector boundary.
以下は parted の出力です。 （これは私のすべてのドライブをリストしているようです。私が関心のある唯一のドライブは、私のRAIDアレイ、sdb、およびsdcを構成するドライブです。）
parted -l /dev/sdb
Model: ATA ST3250318AS (scsi)
Disk /dev/sda: 250GB
Sector size (logical/physical): 512B/512B
Partition Table: msdos
Number Start End Size Type File system Flags
1 1049kB 246GB 246GB primary ext4 boot
2 246GB 250GB 3754MB extended
5 246GB 250GB 3754MB logical linux-swap(v1)
Model: ATA WDC WD40EZRX-00S (scsi)
Disk /dev/sdb: 4001GB
Sector size (logical/physical): 512B/4096B
Partition Table: gpt
Number Start End Size File system Name Flags
1 1049kB 4001GB 4001GB ext3 primary
Model: ATA WDC WD40EZRX-00S (scsi)
Disk /dev/sdc: 4001GB
Sector size (logical/physical): 512B/4096B
Partition Table: gpt
Number Start End Size File system Name Flags
1 1049kB 4001GB 4001GB ext3 primary
Model: ATA ST3000DM001-9YN1 (scsi)
Disk /dev/sdd: 3001GB
Sector size (logical/physical): 512B/4096B
Partition Table: gpt
Number Start End Size File system Name Flags
1 1049kB 3001GB 3001GB ext4 primary msftdata
Model: Seagate Desktop (scsi)
Disk /dev/sde: 3001GB
Sector size (logical/physical): 4096B/4096B
Partition Table: gpt
Number Start End Size File system Name Flags
1 1049kB 3001GB 3001GB Basic data partition msftdata
これは両方のディスクからのgdisk -lの出力です。
gdisk -l /dev/sdb
GPT fdisk (gdisk) version 0.8.8
Partition table scan:
MBR: protective
BSD: not present
APM: not present
GPT: present
Found valid GPT with protective MBR; using GPT.
Disk /dev/sdb: 7814037168 sectors, 3.6 TiB
Logical sector size: 512 bytes
Disk identifier (GUID): DA484D62-BB5D-461B-9F96-EAC8A5815C7B
Partition table holds up to 128 entries
First usable sector is 34, last usable sector is 7814037134
Partitions will be aligned on 2048-sector boundaries
Total free space is 3693 sectors (1.8 MiB)
Number Start (sector) End (sector) Size Code Name
1 2048 7814035455 3.6 TiB 8300 primary
gdisk -l /dev/sdc
GPT fdisk (gdisk) version 0.8.8
Partition table scan:
MBR: protective
BSD: not present
APM: not present
GPT: present
Found valid GPT with protective MBR; using GPT.
Disk /dev/sdc: 7814037168 sectors, 3.6 TiB
Logical sector size: 512 bytes
Disk identifier (GUID): BDE33471-BF86-4B5F-9DAF-5D3E67AE7E40
Partition table holds up to 128 entries
First usable sector is 34, last usable sector is 7814037134
Partitions will be aligned on 2048-sector boundaries
Total free space is 3693 sectors (1.8 MiB)
Number Start (sector) End (sector) Size Code Name
1 2048 7814035455 3.6 TiB 8300 primary
次は何をすべきかわかりません...この配列を修正する方法はありますか？
ベストアンサー1
いくつかの一般的なコメント。
両方のディスクでSMARTを無効にしました（または少なくとも有効にしていません）。実行されたテストはなく、以前に実行されたテストもありません。これが私に知らせるのは、ディスクに欠陥があるかどうかを知る方法がないことです。
カーネルエラーメッセージは、
Add. Sense: Unrecovered read error - auto reallocate failed現在エラーが発生したセクタを交換するために使用できるスペアセクタがなくなったため、ディスクがすぐに致命的なエラーを引き起こすことを示します。これはRAID 0アレイのディスクにとって本当に悪いニュースです。
電源を完全に切って再起動することもできますが、何が起こってもSMARTツールをインストールし、定期的にディスクをテストするように設定することをお勧めします。