TP-Link Archer T2UH AC600ワイヤレスアダプタを購入し、ドライバを正しくコンパイルできましたが、今直面している問題はファイルですRT2870STA.dat。 Linuxシステム用のTP-Linkが提供するマニュアルの指示に従おうとしましたが、空のフィールドを処理する方法は混乱しており、ほとんどのフィールドが何を意味するのか理解していません。
Default
CountryRegion=5
CountryRegionABand=7
CountryCode=CA
SSID=Rogers343 <--#nomyreal SSID
NetworkType=Infra
WirelessMode=9
Channel=0
BeaconPeriod=100
TxPower=100
BGProtection=0
TxPreamble=0
RTSThreshold=2347
FragThreshold=2346
TxBurst=1
WmmCapable=0
AckPolicy=0;0;0;0
AuthMode=WPA2PSK
EncrypType=NONE
WPAPSK=1234567
DefaultKeyID=1
Key1Type=0
Key1Str=
Key2Type=0
Key2Str=
Key3Type=0
Key3Str=
Key4Type=0
Key4Str=
PSMode=CAM
FastRoaming=0
RoamThreshold=70
HT_RDG=1
HT_EXTCHA=0
HT_OpMode=1
HT_MpduDensity=4
HT_BW=1
HT_AutoBA=1
HT_BADecline=0
HT_AMSDU=0
HT_BAWinSize=64
HT_GI=1
HT_MCS=33
HT_MIMOPSMode=3
EthConvertMode=
EthCloneMac=
IEEE80211H=0
TGnWifiTest=0
WirelessEvent=0
MeshId=MESH
MeshAutoLink=1
MeshAuthMode=OPEN
MeshEncrypType=NONE
MeshWPAKEY=
MeshDefaultkey=1
MeshWEPKEY=
CarrierDetect=0
空のフィールドもあり、そこにどの値があるのかわかりません。私のWi-Fi接続名がSSID変更されました。CountryCodeカナダで私の価値がいくらかわかりません。現在使用しているWi-Fi接続なので、入力する必要があるAuthModeようです。ファイルには自動的に何もありません。それが何なのかよく分からない。私のパスワードになります。他の空のフィールドがたくさんありますが、どうすればいいかわかりません。これは、iwprivを使用してKali Linuxでワイヤレスアダプタを設定しようとします。続行する前に、その設定に移動する必要があるためです。また、dhclientを使用してIPを要求できるようにするには、アクセスポイントのSSIDを設定する必要があります。私の質問は、APのSSIDを取得する方法です。 wlan0 インターフェイスの値と ra0 インターフェイスの値を比較すると、wlan0 アクセス ポイントが MAC アドレスのように見えますが、アダプタに MAC アドレスが表示されず、どの値を入れるべきかわかりません。それ。アダプターをセットアップするために実行した手順は次のとおりです。WPAWPA2PersonalEncrypTypeWPAPSKRT2870STA.dat/etc/Wireless/RT2870STA/RT2870STA.datiwpriv
iwpriv ra0 set NetworkType=Infra
iwpriv ra0 set AuthMode=WPA2PSK
iwpriv ra0 set EncrypType=TKIP
iwpriv ra0 set SSID="Rogers343"
iwpriv ra0 set WPAPSK=1234567 <-- not my acutal pswd
iwpriv ra0 set WirelessMode=14
これらのコマンドを入力すると、iwconfig ra0次のようになります。
Ralink STA ESSID:"Rogers343" Nickname:"MT7610U_STA"
Mode:Auto Frequency=5.18 GHz Access Point: Not-Associated
Bit Rate:1 Mb/s
RTS thr:off Fragment thr:off
Encryption key:off
Link Quality=10/100 Signal level:0 dBm Noise level:0 dBm
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0
dmesgアダプタが接続されると出力されます。
3539.786506] usb 1-1.3: new high-speed USB device number 8 using ehci-pci
[ 3539.910506] usb 1-1.3: New USB device found, idVendor=148f, idProduct=761a
[ 3539.910508] usb 1-1.3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 3539.910509] usb 1-1.3: Product: WiFi
[ 3539.910510] usb 1-1.3: Manufacturer: MediaTek
[ 3539.910511] usb 1-1.3: SerialNumber: 1.0
[ 3539.911075]
=== pAd = ffffc64740b25000, size = 892576 ===
[ 3539.911171] <-- RTMPAllocTxRxRingMemory, Status=0
[ 3539.911300] <-- RTMPAllocAdapterBlock, Status=0
[ 3539.911493] ==>RT65xx_WLAN_ChipOnOff(): OnOff:1, Reset= 0, pAd->WlanFunCtrl:0x0, Reg-WlanFunCtrl=0xff000002
[ 3539.912593] MCUType = 2
[ 3539.912869] NVM is EFUSE
[ 3539.912870] Endpoint(8) is for In-band Command
[ 3539.912871] Endpoint(4) is for WMM0 AC0
[ 3539.912871] Endpoint(5) is for WMM0 AC1
[ 3539.912872] Endpoint(6) is for WMM0 AC2
[ 3539.912872] Endpoint(7) is for WMM0 AC3
[ 3539.912873] Endpoint(9) is for WMM1 AC0
[ 3539.912874] Endpoint(84) is for Data-In
[ 3539.912874] Endpoint(85) is for Command Rsp
[ 3632.642059] -->RTUSBVenderReset
[ 3632.642162] <--RTUSBVenderReset
[ 3632.647128] fw version:0.1.00 build:7640
[ 3632.647130] build time:201308221655____
[ 3632.647135] ilm length = 68780(bytes)
[ 3632.647136] dlm length = 11476(bytes)
[ 3632.729684] #
[ 3632.736655] loading fw......
[ 3632.857890] #
[ 3633.074167] RTMP_TimerListAdd: add timer obj ffffc64740ba61e0!
[ 3633.074169] RTMP_TimerListAdd: add timer obj ffffc64740ba6250!
[ 3633.074177] RTMP_TimerListAdd: add timer obj ffffc64740b38c38!
[ 3633.074178] RTMP_TimerListAdd: add timer obj ffffc64740b38e18!
[ 3633.086233] cfg_mode=5
[ 3633.086236] wmode_band_equal(): Band Not Equal!
[ 3633.086350] Key1Str is Invalid key length(0) or Type(0)
[ 3633.086361] Key2Str is Invalid key length(0) or Type(0)
[ 3633.086372] Key3Str is Invalid key length(0) or Type(0)
[ 3633.086383] Key4Str is Invalid key length(0) or Type(0)
[ 3633.086687] 1. Phy Mode = 31
[ 3633.086688] 2. Phy Mode = 31
[ 3633.086690] NVM is Efuse and its size =1d[1e0-1fc]
[ 3633.097715] /root/src/mt7610u_wifi_sta_v3002_dpo_20130916/os/linux/../../chips/mt76x0.c:2114 assert (pAd->TxPower[choffset].Channel == 36)failed
[ 3633.111176] ERROR!!! E2PROM: WRONG VERSION 0x2, should be 1
[ 3633.115302] mt76x0_read_tx_alc_info_from_eeprom: EEPROM_MT76x0_TEMPERATURE_OFFSET (0xD1) = 0xf8
[ 3633.115303] mt76x0_read_tx_alc_info_from_eeprom: TemperatureOffset = 0xfffffff8
[ 3633.115303] Temperature Tx ALC not enabled
[ 3633.130303] 3. Phy Mode = 31
[ 3633.130305] AntCfgInit: primary/secondary ant 0/1
[ 3633.138969] RTMPSetPhyMode: channel is out of range, use first channel=1
[ 3633.140555] MCS Set = ff 00 00 00 01
[ 3633.150491] <==== rt28xx_init, Status=0
[ 3633.151431] 0x1300 = 00064300
[ 3633.151432] RTMPDrvSTAOpen(1):Check if PDMA is idle!
[ 3633.151556] RTMPDrvSTAOpen(2):Check if PDMA is idle!
[ 4260.799872] receive cmd msg fail(-71)
[ 4260.799965] Bulk In Failed. Status=-71, BIIdx=0x0, BIRIdx=0x0, actual_length= 0x0
[ 4260.804373] receive cmd msg fail(-71)
[ 4260.832271] #
[ 4260.834242] receive cmd msg fail(-71)
[ 4260.838494] receive cmd msg fail(-71)
[ 4260.841272] #
[ 4260.842743] receive cmd msg fail(-71)
[ 4260.846994] receive cmd msg fail(-71)
[ 4260.850247] #
[ 4260.851243] receive cmd msg fail(-71)
[ 4260.855520] receive cmd msg fail(-71)
[ 4260.859274] #
[ 4260.996257] receive cmd msg fail(-71)
[ 4260.998887] #
[ 4261.000507] receive cmd msg fail(-71)
[ 4261.003855] RTUSB_VendorRequest failed(-71),TxFlags=0x0, ReqType=IN, Req=0x7, Idx=0x1000,pAd->Flags=0x31080002
[ 4261.004758] receive cmd msg fail(-71)
[ 4261.007759] Bulk In Failed. Status=-71, BIIdx=0x0, BIRIdx=0x0, actual_length= 0x0
[ 4261.009009] receive cmd msg fail(-71)
[ 4261.030639] #
[ 4261.034139] usb 1-1.3: USB disconnect, device number 8
[ 4261.034509] receive cmd msg fail(-108)
[ 4261.034511] usb_rx_cmd_msg_complete:submit urb fail(-19)
[ 4261.034517] usb_rx_cmd_msg_submit:submit urb fail(-19)
[ 4261.034519] rtusb_disconnect: unregister usbnet usb-0000:00:1d.0-1.3
[ 4261.034522] RtmpOSNetDevDetach(): RtmpOSNetDeviceDetach(), dev->name=ra0!
[ 4261.035606] #
[ 4261.035608] RTUSB_VendorRequest failed(-19),TxFlags=0x0, ReqType=IN, Req=0x7, Idx=0x1000,pAd->Flags=0x31080542
[ 4261.035609] CMDTHREAD_RESET_BULK_IN: Cannot do bulk in because flags(0x31080542) on !
[ 4261.049617] WIFI device has been disconnected
[ 4261.049668] WIFI device has been disconnected
[ 4261.049668] WIFI device has been disconnected
[ 4261.049669] WIFI device has been disconnected
[ 4261.049673] tx_kickout_fail_count = 0
[ 4261.049673] tx_timeout_fail_count = 0
[ 4261.049674] rx_receive_fail_count = 58
[ 4261.049674] alloc_cmd_msg = 7672
[ 4261.049675] free_cmd_msg = 7672
[ 4261.132674] WIFI device has been disconnected
[ 4261.132677] ==>RT65xx_WLAN_ChipOnOff(): OnOff:0, Reset= 0, pAd->WlanFunCtrl:0xff000003, Reg-WlanFunCtrl=0xffffffff
[ 4261.132677] WIFI device has been disconnected
[ 4261.132678] VendrCmdMultiWrite_nBytes failed!
[ 4261.132698] WIFI device has been disconnected
[ 4261.132708] ---> RTMPFreeTxRxRingMemory
[ 4261.132722] <--- RTMPFreeTxRxRingMemory
[ 4261.132759] RTUSB disconnect successfully
[ 4981.190839] usb 1-1.3: new high-speed USB device number 9 using ehci-pci
[ 4981.315282] usb 1-1.3: New USB device found, idVendor=148f, idProduct=761a
[ 4981.315284] usb 1-1.3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 4981.315285] usb 1-1.3: Product: WiFi
[ 4981.315286] usb 1-1.3: Manufacturer: MediaTek
[ 4981.315287] usb 1-1.3: SerialNumber: 1.0
[ 4981.315819]
=== pAd = ffffc64740b25000, size = 892576 ===
[ 4981.315904] <-- RTMPAllocTxRxRingMemory, Status=0
[ 4981.316006] <-- RTMPAllocAdapterBlock, Status=0
[ 4981.316133] ==>RT65xx_WLAN_ChipOnOff(): OnOff:1, Reset= 0, pAd->WlanFunCtrl:0x0, Reg-WlanFunCtrl=0xff000002
[ 4981.317259] MCUType = 2
[ 4981.317507] NVM is EFUSE
[ 4981.317508] Endpoint(8) is for In-band Command
[ 4981.317509] Endpoint(4) is for WMM0 AC0
[ 4981.317509] Endpoint(5) is for WMM0 AC1
[ 4981.317510] Endpoint(6) is for WMM0 AC2
[ 4981.317511] Endpoint(7) is for WMM0 AC3
[ 4981.317511] Endpoint(9) is for WMM1 AC0
[ 4981.317512] Endpoint(84) is for Data-In
[ 4981.317512] Endpoint(85) is for Command Rsp
その後、これを実行しましたが、systemctl restart network-manager.service
ネットワークから追い出されましたが、ネットワーク管理者に両方のWi-Fiアイコンが表示されることがわかりましたが、下の画像に示すように、両方のカードが「使用できません」と表示され、ネットワークは選択されません。
dmesgこれが発生した後の結果です。
238.916761] bluetooth hci0: firmware: failed to load brcm/BCM.hcd (-2)
[ 238.916766] bluetooth hci0: Direct firmware load for brcm/BCM.hcd failed with error -2
[ 238.916769] Bluetooth: hci0: BCM: Patch brcm/BCM.hcd not found
[ 239.115808] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 239.310935] r8169 0000:07:00.0 eth0: link down
[ 239.310991] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 239.311865] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 240.719041] atkbd serio0: Unknown key pressed (translated set 2, code 0x8d on isa0060/serio0).
[ 240.719043] atkbd serio0: Use 'setkeycodes e00d <keycode>' to make it known.
[ 285.069677] ERROR @wl_notify_scan_status : wlan0 Scan_results error (-22)
[ 954.235212] perf: interrupt took too long (2506 > 2500), lowering kernel.perf_event_max_sample_rate to 79750
[ 1193.231540] perf: interrupt took too long (3135 > 3132), lowering kernel.perf_event_max_sample_rate to 63750
[ 1470.857282] perf: interrupt took too long (4013 > 3918), lowering kernel.perf_event_max_sample_rate to 49750
[ 2345.359889] perf: interrupt took too long (5032 > 5016), lowering kernel.perf_event_max_sample_rate to 39500
[ 3539.786506] usb 1-1.3: new high-speed USB device number 8 using ehci-pci
[ 3539.910506] usb 1-1.3: New USB device found, idVendor=148f, idProduct=761a
[ 3539.910508] usb 1-1.3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 3539.910509] usb 1-1.3: Product: WiFi
[ 3539.910510] usb 1-1.3: Manufacturer: MediaTek
[ 3539.910511] usb 1-1.3: SerialNumber: 1.0
[ 3539.911075]
=== pAd = ffffc64740b25000, size = 892576 ===
[ 3539.911171] <-- RTMPAllocTxRxRingMemory, Status=0
[ 3539.911300] <-- RTMPAllocAdapterBlock, Status=0
[ 3539.911493] ==>RT65xx_WLAN_ChipOnOff(): OnOff:1, Reset= 0, pAd->WlanFunCtrl:0x0, Reg-WlanFunCtrl=0xff000002
[ 3539.912593] MCUType = 2
[ 3539.912869] NVM is EFUSE
[ 3539.912870] Endpoint(8) is for In-band Command
[ 3539.912871] Endpoint(4) is for WMM0 AC0
[ 3539.912871] Endpoint(5) is for WMM0 AC1
[ 3539.912872] Endpoint(6) is for WMM0 AC2
[ 3539.912872] Endpoint(7) is for WMM0 AC3
[ 3539.912873] Endpoint(9) is for WMM1 AC0
[ 3539.912874] Endpoint(84) is for Data-In
[ 3539.912874] Endpoint(85) is for Command Rsp
[ 3632.642059] -->RTUSBVenderReset
[ 3632.642162] <--RTUSBVenderReset
[ 3632.647128] fw version:0.1.00 build:7640
[ 3632.647130] build time:201308221655____
[ 3632.647135] ilm length = 68780(bytes)
[ 3632.647136] dlm length = 11476(bytes)
[ 3632.729684] #
[ 3632.736655] loading fw......
[ 3632.857890] #
[ 3633.074167] RTMP_TimerListAdd: add timer obj ffffc64740ba61e0!
[ 3633.074169] RTMP_TimerListAdd: add timer obj ffffc64740ba6250!
[ 3633.074170] RTMP_TimerListAdd: add timer obj ffffc64740ba62c0!
[ 3633.074171] RTMP_TimerListAdd: add timer obj ffffc64740ba6170!
[ 3633.086233] cfg_mode=5
[ 3633.086236] wmode_band_equal(): Band Not Equal!
[ 3633.086350] Key1Str is Invalid key length(0) or Type(0)
[ 3633.086361] Key2Str is Invalid key length(0) or Type(0)
[ 3633.086372] Key3Str is Invalid key length(0) or Type(0)
[ 3633.086383] Key4Str is Invalid key length(0) or Type(0)
[ 3633.086687] 1. Phy Mode = 31
[ 3633.086688] 2. Phy Mode = 31
[ 3633.086690] NVM is Efuse and its size =1d[1e0-1fc]
[ 3633.097715] /root/src/mt7610u_wifi_sta_v3002_dpo_20130916/os/linux/../../chips/mt76x0.c:2114 assert (pAd->TxPower[choffset].Channel == 36)failed
[ 3633.111176] ERROR!!! E2PROM: WRONG VERSION 0x2, should be 1
[ 3633.115302] mt76x0_read_tx_alc_info_from_eeprom: EEPROM_MT76x0_TEMPERATURE_OFFSET (0xD1) = 0xf8
[ 3633.115303] mt76x0_read_tx_alc_info_from_eeprom: TemperatureOffset = 0xfffffff8
[ 3633.115303] Temperature Tx ALC not enabled
[ 3633.130303] 3. Phy Mode = 31
[ 3633.130305] AntCfgInit: primary/secondary ant 0/1
[ 3633.138969] RTMPSetPhyMode: channel is out of range, use first channel=1
[ 3633.140555] MCS Set = ff 00 00 00 01
[ 3633.150491] <==== rt28xx_init, Status=0
[ 3633.151431] 0x1300 = 00064300
[ 3633.151432] RTMPDrvSTAOpen(1):Check if PDMA is idle!
[ 3633.151556] RTMPDrvSTAOpen(2):Check if PDMA is idle!
[ 4260.799872] receive cmd msg fail(-71)
[ 4260.799965] Bulk In Failed. Status=-71, BIIdx=0x0, BIRIdx=0x0, actual_length= 0x0
[ 4260.804373] receive cmd msg fail(-71)
[ 4260.808616] receive cmd msg fail(-71)
[ 4260.812867] receive cmd msg fail(-71)
[ 4260.817116] receive cmd msg fail(-71)
[ 4260.898248] receive cmd msg fail(-71)
[ 4260.900248] RTUSB_VendorRequest failed(-71),TxFlags=0x0, ReqType=IN, Req=0x7, Idx=0x1000,pAd->Flags=0x31080002
[ 4260.902500] receive cmd msg fail(-71)
[ 4260.904250] Bulk In Failed. Status=-71, BIIdx=0x0, BIRIdx=0x0, actual_length= 0x0
[ 4260.945005] receive cmd msg fail(-71)
[ 4261.000507] receive cmd msg fail(-71)
[ 4261.003855] RTUSB_VendorRequest failed(-71),TxFlags=0x0, ReqType=IN, Req=0x7, Idx=0x1000,pAd->Flags=0x31080002
[ 4261.004758] receive cmd msg fail(-71)
[ 4261.007759] Bulk In Failed. Status=-71, BIIdx=0x0, BIRIdx=0x0, actual_length= 0x0
[ 4261.009009] receive cmd msg fail(-71)
[ 4261.034139] usb 1-1.3: USB disconnect, device number 8
[ 4261.034509] receive cmd msg fail(-108)
[ 4261.034511] usb_rx_cmd_msg_complete:submit urb fail(-19)
[ 4261.034517] usb_rx_cmd_msg_submit:submit urb fail(-19)
[ 4261.034519] rtusb_disconnect: unregister usbnet usb-0000:00:1d.0-1.3
[ 4261.034522] RtmpOSNetDevDetach(): RtmpOSNetDeviceDetach(), dev->name=ra0!
[ 4261.035606] #
[ 4261.035608] RTUSB_VendorRequest failed(-19),TxFlags=0x0, ReqType=IN, Req=0x7, Idx=0x1000,pAd->Flags=0x31080542
[ 4261.035609] CMDTHREAD_RESET_BULK_IN: Cannot do bulk in because flags(0x31080542) on !
[ 4261.049617] WIFI device has been disconnected
[ 4261.049668] WIFI device has been disconnected
[ 4261.049668] WIFI device has been disconnected
[ 4261.049669] WIFI device has been disconnected
[ 4261.049673] tx_kickout_fail_count = 0
[ 4261.049673] tx_timeout_fail_count = 0
[ 4261.049674] rx_receive_fail_count = 58
[ 4261.049674] alloc_cmd_msg = 7672
[ 4261.049675] free_cmd_msg = 7672
[ 4261.132674] WIFI device has been disconnected
[ 4261.132677] ==>RT65xx_WLAN_ChipOnOff(): OnOff:0, Reset= 0, pAd->WlanFunCtrl:0xff000003, Reg-WlanFunCtrl=0xffffffff
[ 4261.132677] WIFI device has been disconnected
[ 4261.132678] VendrCmdMultiWrite_nBytes failed!
[ 4261.132698] WIFI device has been disconnected
[ 4261.132708] ---> RTMPFreeTxRxRingMemory
[ 4261.132722] <--- RTMPFreeTxRxRingMemory
[ 4261.132759] RTUSB disconnect successfully
[ 4981.190839] usb 1-1.3: new high-speed USB device number 9 using ehci-pci
[ 4981.315282] usb 1-1.3: New USB device found, idVendor=148f, idProduct=761a
[ 4981.315284] usb 1-1.3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 4981.315285] usb 1-1.3: Product: WiFi
[ 4981.315286] usb 1-1.3: Manufacturer: MediaTek
[ 4981.315287] usb 1-1.3: SerialNumber: 1.0
[ 4981.315819]
=== pAd = ffffc64740b25000, size = 892576 ===
[ 4981.315904] <-- RTMPAllocTxRxRingMemory, Status=0
[ 4981.316006] <-- RTMPAllocAdapterBlock, Status=0
[ 4981.316133] ==>RT65xx_WLAN_ChipOnOff(): OnOff:1, Reset= 0, pAd->WlanFunCtrl:0x0, Reg-WlanFunCtrl=0xff000002
[ 4981.317259] MCUType = 2
[ 4981.317507] NVM is EFUSE
[ 4981.317508] Endpoint(8) is for In-band Command
[ 4981.317509] Endpoint(4) is for WMM0 AC0
[ 4981.317509] Endpoint(5) is for WMM0 AC1
[ 4981.317510] Endpoint(6) is for WMM0 AC2
[ 4981.317511] Endpoint(7) is for WMM0 AC3
[ 4981.317511] Endpoint(9) is for WMM1 AC0
[ 4981.317512] Endpoint(84) is for Data-In
[ 4981.317512] Endpoint(85) is for Command Rsp
[ 5382.065830] -->RTUSBVenderReset
[ 5382.066025] <--RTUSBVenderReset
[ 5382.070992] fw version:0.1.00 build:7640
[ 5382.070994] build time:201308221655____
[ 5382.071000] ilm length = 68780(bytes)
[ 5382.071000] dlm length = 11476(bytes)
[ 5382.152631] #
[ 5382.158632] loading fw......
[ 5382.276688] #
[ 5382.494398] RTMP_TimerListAdd: add timer obj ffffc64740ba61e0!
[ 5382.494400] RTMP_TimerListAdd: add timer obj ffffc64740ba6250!
[ 5382.494401] RTMP_TimerListAdd: add timer obj ffffc64740ba62c0!
[ 5382.494402] RTMP_TimerListAdd: add timer obj ffffc64740ba6170!
[ 5382.494408] RTMP_TimerListAdd: add timer obj ffffc64740b38c38!
[ 5382.494409] RTMP_TimerListAdd: add timer obj ffffc64740b38e18!
[ 5382.494466] cfg_mode=5
[ 5382.494468] wmode_band_equal(): Band Not Equal!
[ 5382.494582] Key1Str is Invalid key length(0) or Type(0)
[ 5382.494593] Key2Str is Invalid key length(0) or Type(0)
[ 5382.494604] Key3Str is Invalid key length(0) or Type(0)
[ 5382.494616] Key4Str is Invalid key length(0) or Type(0)
[ 5382.494856] 1. Phy Mode = 31
[ 5382.494856] 2. Phy Mode = 31
[ 5382.494858] NVM is Efuse and its size =1d[1e0-1fc]
[ 5382.506903] /root/src/mt7610u_wifi_sta_v3002_dpo_20130916/os/linux/../../chips/mt76x0.c:2114 assert (pAd->TxPower[choffset].Channel == 36)failed
[ 5382.517405] ERROR!!! E2PROM: WRONG VERSION 0x2, should be 1
[ 5382.521530] mt76x0_read_tx_alc_info_from_eeprom: EEPROM_MT76x0_TEMPERATURE_OFFSET (0xD1) = 0xf8
[ 5382.521531] mt76x0_read_tx_alc_info_from_eeprom: TemperatureOffset = 0xfffffff8
[ 5382.521532] Temperature Tx ALC not enabled
[ 5382.537531] 3. Phy Mode = 31
[ 5382.537533] AntCfgInit: primary/secondary ant 0/1
[ 5382.542790] RTMPSetPhyMode: channel is out of range, use first channel=1
[ 5382.544283] MCS Set = ff 00 00 00 01
[ 5382.554214] <==== rt28xx_init, Status=0
[ 5382.555157] 0x1300 = 00064300
[ 5382.555158] RTMPDrvSTAOpen(1):Check if PDMA is idle!
[ 5382.555314] RTMPDrvSTAOpen(2):Check if PDMA is idle!
[ 5482.218330] ===>rt_ioctl_giwscan. 2(2) BSS returned, data->length = 317
[ 5550.260554] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 5550.293209] ERROR!!! RTMPSetTimer failed, Halt in Progress!
[ 5550.300208] ==>RT65xx_WLAN_ChipOnOff(): OnOff:0, Reset= 0, pAd->WlanFunCtrl:0xff000003, Reg-WlanFunCtrl=0xff000003
[ 5550.303830] receive cmd msg fail(-2)
[ 5550.303842] tx_kickout_fail_count = 0
[ 5550.303844] tx_timeout_fail_count = 0
[ 5550.303845] rx_receive_fail_count = 0
[ 5550.303846] alloc_cmd_msg = 6981
[ 5550.303846] free_cmd_msg = 6981
[ 5550.359595] ==>RT65xx_WLAN_ChipOnOff(): OnOff:1, Reset= 0, pAd->WlanFunCtrl:0xff000000, Reg-WlanFunCtrl=0xff000000
[ 5550.366721] -->RTUSBVenderReset
[ 5550.366846] <--RTUSBVenderReset
[ 5550.371809] fw version:0.1.00 build:7640
[ 5550.371811] build time:201308221655____
[ 5550.371825] ilm length = 68780(bytes)
[ 5550.371825] dlm length = 11476(bytes)
[ 5550.451175] #
[ 5550.457901] loading fw......
[ 5550.796383] RTMP_TimerListAdd: add timer obj ffffc64740b38d18!
[ 5550.796384] RTMP_TimerListAdd: add timer obj ffffc64740b27b80!
[ 5550.796384] RTMP_TimerListAdd: add timer obj ffffc64740b27bf8!
[ 5550.796385] RTMP_TimerListAdd: add timer obj ffffc64740b38e88!
[ 5550.796386] RTMP_TimerListAdd: add timer obj ffffc64740b38c38!
[ 5550.796387] RTMP_TimerListAdd: add timer obj ffffc64740b38e18!
[ 5550.796444] cfg_mode=5
[ 5550.796446] wmode_band_equal(): Band Not Equal!
[ 5550.796559] Key1Str is Invalid key length(0) or Type(0)
[ 5550.796570] Key2Str is Invalid key length(0) or Type(0)
[ 5550.796581] Key3Str is Invalid key length(0) or Type(0)
[ 5550.796592] Key4Str is Invalid key length(0) or Type(0)
[ 5550.796832] 1. Phy Mode = 31
[ 5550.796833] 2. Phy Mode = 31
[ 5550.796834] NVM is Efuse and its size =1d[1e0-1fc]
[ 5550.807751] /root/src/mt7610u_wifi_sta_v3002_dpo_20130916/os/linux/../../chips/mt76x0.c:2114 assert (pAd->TxPower[choffset].Channel == 36)failed
[ 5550.818252] ERROR!!! E2PROM: WRONG VERSION 0x2, should be 1
[ 5550.822377] mt76x0_read_tx_alc_info_from_eeprom: EEPROM_MT76x0_TEMPERATURE_OFFSET (0xD1) = 0xf8
[ 5550.822378] mt76x0_read_tx_alc_info_from_eeprom: TemperatureOffset = 0xfffffff8
[ 5550.822378] Temperature Tx ALC not enabled
[ 5550.839378] 3. Phy Mode = 31
[ 5550.839379] AntCfgInit: primary/secondary ant 0/1
[ 5550.844637] RTMPSetPhyMode: channel is out of range, use first channel=1
[ 5550.846035] MCS Set = ff 00 00 00 01
[ 5550.855972] <==== rt28xx_init, Status=0
[ 5550.857128] 0x1300 = 00064300
[ 5550.857129] RTMPDrvSTAOpen(1):Check if PDMA is idle!
[ 5550.857255] RTMPDrvSTAOpen(2):Check if PDMA is idle!
[ 5551.014244] BUG: unable to handle kernel paging request at 00007fff13453d00
[ 5551.014316] IP: [<ffffffffc0df441a>] rt_ioctl_siwpmksa+0x8a/0x140 [mt7650u_sta]
[ 5551.014402] PGD 116cca067 PUD 11599c067 PMD 117fd0067 PTE 800000010a6d3867
[ 5551.014467] Oops: 0001 [#1] SMP
[ 5551.014494] Modules linked in: fuse nfnetlink_queue nfnetlink_log nfnetlink binfmt_misc wl(PO) mt7650u_sta(O) snd_hda_codec_hdmi intel_rapl x86_pkg_temp_thermal intel_powerclamp coretemp btusb btrtl btbcm btintel uvcvideo bluetooth videobuf2_vmalloc kvm_intel dcdbas videobuf2_memops iTCO_wdt snd_hda_codec_realtek videobuf2_v4l2 iTCO_vendor_support kvm hid_rmi dell_smm_hwmon videobuf2_core videodev irqbypass snd_hda_codec_generic cfg80211 snd_hda_intel rtsx_usb_ms hid_multitouch memstick pcspkr media snd_soc_rt5640 snd_hda_codec snd_soc_ssm4567 snd_soc_rl6231 snd_soc_core snd_hda_core joydev evdev snd_hwdep snd_compress snd_pcm sg serio_raw i915 wmi snd_timer snd shpchp dw_dmac battery video elan_i2c dell_rbtn rfkill i2c_i801 dw_dmac_core snd_soc_sst_acpi mei_me mei snd_soc_sst_match lpc_ich drm_kms_helper
[ 5551.015186] soundcore i2c_smbus acpi_pad ac button drm i2c_algo_bit tpm_tis tpm_tis_core tpm i2c_designware_platform i2c_designware_core ip_tables x_tables autofs4 rtsx_usb_sdmmc rtsx_usb mfd_core ext4 crc16 usbhid jbd2 crc32c_generic fscrypto ecb mbcache sr_mod cdrom sd_mod crct10dif_pclmul crc32_pclmul crc32c_intel ghash_clmulni_intel aesni_intel aes_x86_64 lrw gf128mul glue_helper ablk_helper cryptd ahci libahci psmouse xhci_pci xhci_hcd libata ehci_pci ehci_hcd scsi_mod r8169 mii usbcore usb_common fan thermal sdhci_acpi sdhci mmc_core fjes i2c_hid hid
[ 5551.015700] CPU: 0 PID: 838 Comm: wpa_supplicant Tainted: P O 4.8.0-kali1-amd64 #1 Debian 4.8.5-1kali1
[ 5551.015775] Hardware name: Dell Inc. Inspiron 3543/0MGXC6, BIOS A00 10/25/2014
[ 5551.015832] task: ffff906d98270080 task.stack: ffff906d934a4000
[ 5551.015874] RIP: 0010:[<ffffffffc0df441a>] [<ffffffffc0df441a>] rt_ioctl_siwpmksa+0x8a/0x140 [mt7650u_sta]
[ 5551.015974] RSP: 0018:ffff906d934a7ca8 EFLAGS: 00010297
[ 5551.016016] RAX: 0000000000000000 RBX: 00007fff13453d00 RCX: 0000000000000000
[ 5551.016067] RDX: 0000000000005013 RSI: 0000000000000000 RDI: ffffc64740b25000
[ 5551.016119] RBP: 0000000000000000 R08: 0000000000000000 R09: 0000000000000000
[ 5551.016169] R10: 0000000000000036 R11: ffffffffc0df4390 R12: ffffc64740b25000
[ 5551.016224] R13: ffff906d0ca3d000 R14: ffffffff8429a888 R15: ffffffffc0df4390
[ 5551.016275] FS: 00007f275db5a880(0000) GS:ffff906d9ec00000(0000) knlGS:0000000000000000
[ 5551.016338] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 5551.016382] CR2: 00007fff13453d00 CR3: 0000000116c12000 CR4: 00000000003406f0
[ 5551.016437] Stack:
[ 5551.016456] ffff906cacae6a00 ffff906d941d1000 ffff906d93dbd900 0000000000000024
[ 5551.016522] 000000005485238f ffff906d2a0b0540 ffff906d934a7e20 0000000000000000
[ 5551.016586] 0000000000008b36 ffffffff841ce8b8 ffff906d0ca3d000 00007fff13453d00
[ 5551.016652] Call Trace:
[ 5551.016681] [<ffffffff841ce8b8>] ? ioctl_standard_iw_point+0x2e8/0x3c0
[ 5551.016734] [<ffffffff841cea3a>] ? ioctl_standard_call+0xaa/0xd0
[ 5551.016783] [<ffffffff841cec55>] ? wext_handle_ioctl+0x75/0xd0
[ 5551.016828] [<ffffffff840fa62f>] ? dev_ioctl+0x29f/0x580
[ 5551.016871] [<ffffffff840bf8bd>] ? sock_ioctl+0x11d/0x280
[ 5551.016916] [<ffffffff83e1334f>] ? do_vfs_ioctl+0x9f/0x5f0
[ 5551.016962] [<ffffffff83dff6d0>] ? vfs_read+0x90/0x130
[ 5551.017006] [<ffffffff83e13914>] ? SyS_ioctl+0x74/0x80
[ 5551.017047] [<ffffffff841e18f6>] ? system_call_fast_compare_end+0xc/0x96
[ 5551.017100] Code: 00 bd 9c ff ff ff eb 78 48 85 db 0f 84 a0 00 00 00 48 83 3d 40 23 04 00 02 89 c5 76 0e 48 83 3d 5c a5 06 00 00 0f 84 a5 00 00 00 <8b> 03 83 f8 03 74 6b 83 f8 02 74 70 83 f8 01 0f 94 c0 0f b6 c0
[ 5551.017394] RIP [<ffffffffc0df441a>] rt_ioctl_siwpmksa+0x8a/0x140 [mt7650u_sta]
[ 5551.017477] RSP <ffff906d934a7ca8>
[ 5551.017504] CR2: 00007fff13453d00
[ 5551.027427] ---[ end trace 59de0c89298499a0 ]---
ベストアンサー1
これは既存のノートブック（RT5390を含むHP g6）で行う必要がありました。
一度入力したが必須ではないssidを含む多くのフィールドが空です。
最も重要なことは、ビルド前に編集する必要があるいくつかのファイルがあることです。
確認するために古いラップトップを起動しました...tarを再抽出してマージしました...
構成ファイル
HAS_NATIVE_WPA_SUPPLICANT_SUPPORT=n
changed to:
HAS_NATIVE_WPA_SUPPLICANT_SUPPORT=y
pci_main_dev.c
いくつかのブロックロジックをコメントアウトしました。
SET_NETDEV_DEV(net_dev,&(pci-dev->dev))
（ネットワーク管理者はそれなしではサポートされていませんが、ロジックはカーネル2.6.0用です。実際、そのカーネルに以前のカーネルがあったかどうか覚えていません...ある時点でそうしたことがあります）。
rt_linux.c
skb->tailを編集してunsigned int 32ビットに変換しました。
最後にmakefileから：
- 周辺ロジックを削除し、 ;chipset=5390 に変更しました。
- すべてのPCプラットフォームを削除しました。
- MAKE MAKE = makeに関するすべてのロジックを削除しました。
（今はより良いバージョンがあると思うので、このステップをすべて実行する必要はありませんが、そこにあります...）
datファイルに関して3xの値を変更しました（ただし、後で行ったようにネットワーク管理者用にコンパイルする場合は必要ありません）。
- SSID=
- EncrypType=wpa-psk
- WPAPSK=
すべてのビルドが完了したら、datファイルを挿入します。
/etc/Wireless/RT5390STA/RT5390STA.dat
/etc/Wireless/RT5390STA/RT5390STACard.dat
ご希望または役に立つ場合は、比較のために.datファイルをコピーしてください。
アップデート：ブラックリストに使用するモジュールを見つけます。
sudo lscpi -v | less
現在のコンピュータの出力例
03:00.0 Network controller: Intel Corporation Wireless 3165 (rev 81)
DeviceName: SP1
Subsystem: Intel Corporation Dual Band Wireless AC 3165
Flags: bus master, fast devsel, latency 0, IRQ 42
Memory at f1000000 (64-bit, non-prefetchable) [size=8K]
Capabilities: [c8] Power Management version 3
Capabilities: [d0] MSI: Enable+ Count=1/1 Maskable- 64bit+
Capabilities: [40] Express Endpoint, MSI 00
Capabilities: [100] Advanced Error Reporting
Capabilities: [140] Device Serial Number dc-53-60-ff-ff-5f-cb-f2
Capabilities: [14c] Latency Tolerance Reporting
Capabilities: [154] L1 PM Substates
Kernel driver in use: iwlwifi
Kernel modules: iwlwifi
この場合、/etc/modprobe.d/wifi.confにブラックリストを追加します。
blacklist iwlwifi
ワイヤレスデバイスに次のものが表示されるまでこれを繰り返します。
Kernel driver in use: rt2800pci
修正する:
私のtp-link USBアダプタを見つけました（OPはpciデバイスではなくUSBを揃えようとしていました）。
まだUSBソースコードをコンパイルしていません。これは、すでに利用可能なカーネルとファームウェアのBLOBでのみ機能します。
[ 25.502040] usb 2-1: new high-speed USB device number 2 using xhci_hcd
[ 25.660113] usb 2-1: New USB device found, idVendor=148f, idProduct=5572
[ 25.660124] usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 25.660129] usb 2-1: Product: 802.11 n WLAN
[ 25.660133] usb 2-1: Manufacturer: Ralink
[ 25.660136] usb 2-1: SerialNumber: 1.0
[ 25.827234] usb 2-1: reset high-speed USB device number 2 using xhci_hcd
[ 25.977689] ieee80211 phy1: rt2x00_set_rt: Info - RT chipset 5592, rev 0222 detected
[ 26.088458] ieee80211 phy1: rt2x00_set_rf: Info - RF chipset 000f detected
[ 26.090545] ieee80211 phy1: Selected rate control algorithm 'minstrel_ht'
[ 26.092720] usbcore: registered new interface driver rt2800usb
[ 26.122102] ieee80211 phy1: rt2x00lib_request_firmware: Info - Loading firmware file 'rt2870.bin'
[ 26.122379] ieee80211 phy1: rt2x00lib_request_firmware: Info - Firmware detected - version: 0.29
現在のカーネルモジュールは次のとおりです。
$ lsmod | grep rt2
rt2800usb 28672 0
rt2x00usb 20480 1 rt2800usb
rt2800lib 81920 1 rt2800usb
rt2x00lib 45056 3 rt2800lib,rt2800usb,rt2x00usb
crc_ccitt 16384 1 rt2800lib
mac80211 569344 4 rt2800lib,iwlmvm,rt2x00lib,rt2x00usb
cfg80211 471040 4 iwlmvm,iwlwifi,rt2x00lib,mac80211
usbcore 208896 6 rt2800usb,rt2x00usb,ehci_hcd,xhci_pci,xhci_hcd,ehci_pci
ファームウェアブロブは、次のパッケージで提供されます。
firmware-misc-nonfree: /lib/firmware/rt2870.bin
OPが必要な場合は、このUSBデバイスを使用してソースパッケージをテストできますか？