背景
私が新しいWD Red 3TBディスクでサーバーを構築したとき、おそらく深刻な判断エラーを犯し、古くて非常に古いSATA（ウィキペディア）ケーブル。私の質問は、本質的にハードウェアの背景とDebian 10 Linuxシステムで実行されているいくつかの履歴についてです。
私が言うケーブルは2本です。
5歳以上ですが、まだSATA III認証されたデータケーブル。 IMHO これは過度に曲がると問題が発生する可能性がありますが、乱用については認識できないので、シールドが長年にわたってより良くなったはずです（？）待つようです。
同じサーバーにいることに驚きました。SATAケーブルは15年以上経過している可能性があります。ただシリアルATA
mdadm以上を書いて、dmesgさまざまなディスクI / Oエラーメッセージの形でこのサーバーを構成した後、RAID 1アレイにはますます小さな問題が発生し、最終的にアレイのパフォーマンスが低下することを考慮してWonderingを書き込みます。これらのケーブルのいずれかまたは両方のケーブルがアレイを読み書きするときにエラーが発生する可能性があります。
ケーブルの交換
今日私がしたことはドイツ産（ステッカーに書かれている）2つを購入したのですが、おそらくより高品質、SATA III認定新しいケーブル、何が起こっているのかを確認してください。
テスト
サーバーを起動し、アレイをマウント解除して停止しました。
一晩、この2つの別々のディスク読み取りコマンドの実行を開始しました。
pv < /dev/sdX > /dev/nullまた、エラー
dmesgと速度の監視を開始しましたnmon。 1時間経っても、現在までエラーや速度低下はありません...
質問
dmesg私が目を覚まし、このドライブがエラーなしで完全に読んでいることを発見したと仮定すると、古いケーブルがエラーの原因であると仮定できますか、それとも私が考慮していないものがありますか？
ここに投稿するかスーパーユーザーに投稿するかを決定することはできません。他の場所がより適切な場合は、このようなコメントがたくさん実行されたら、朝に再び上げます。とにかくお時間をいただきありがとうございます。
smartctl
WD-WCC4N6EZXNSD
smartctl 6.6 2017-11-05 r4594 [x86_64-linux-4.19.0-9-amd64] (local build)
Copyright (C) 2002-17, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Western Digital Red
Device Model: WDC WD30EFRX-68EUZN0
Serial Number: WD-WCC4N6EZXNSD
LU WWN Device Id: 5 0014ee 210a9a0ef
Firmware Version: 82.00A82
User Capacity: 3,000,592,982,016 bytes [3.00 TB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Rotation Rate: 5400 rpm
Device is: In smartctl database [for details use: -P show]
ATA Version is: ACS-2 (minor revision not indicated)
SATA Version is: SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is: Sat Jun 20 08:47:05 2020 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: (40380) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 405) minutes.
Conveyance self-test routine
recommended polling time: ( 5) minutes.
SCT capabilities: (0x703d) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x002f 200 200 051 Pre-fail Always - 0
3 Spin_Up_Time 0x0027 179 178 021 Pre-fail Always - 6050
4 Start_Stop_Count 0x0032 100 100 000 Old_age Always - 31
5 Reallocated_Sector_Ct 0x0033 200 200 140 Pre-fail Always - 0
7 Seek_Error_Rate 0x002e 100 253 000 Old_age Always - 0
9 Power_On_Hours 0x0032 097 097 000 Old_age Always - 2443
10 Spin_Retry_Count 0x0032 100 253 000 Old_age Always - 0
11 Calibration_Retry_Count 0x0032 100 253 000 Old_age Always - 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 31
192 Power-Off_Retract_Count 0x0032 200 200 000 Old_age Always - 3
193 Load_Cycle_Count 0x0032 200 200 000 Old_age Always - 2423
194 Temperature_Celsius 0x0022 116 109 000 Old_age Always - 34
196 Reallocated_Event_Count 0x0032 200 200 000 Old_age Always - 0
197 Current_Pending_Sector 0x0032 200 200 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0030 100 253 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x0032 200 200 000 Old_age Always - 0
200 Multi_Zone_Error_Rate 0x0008 100 253 000 Old_age Offline - 0
SMART Error Log Version: 1
ATA Error Count: 2033 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 2033 occurred at disk power-on lifetime: 424 hours (17 days + 16 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
04 61 02 00 00 00 a0 Device Fault; Error: ABRT
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
ef 10 02 00 00 00 a0 00 2d+13:04:28.795 SET FEATURES [Enable SATA feature]
ec 00 00 00 00 00 a0 00 2d+13:04:28.794 IDENTIFY DEVICE
ef 03 46 00 00 00 a0 00 2d+13:04:28.794 SET FEATURES [Set transfer mode]
ef 10 02 00 00 00 a0 00 2d+13:04:28.794 SET FEATURES [Enable SATA feature]
ec 00 00 00 00 00 a0 00 2d+13:04:28.793 IDENTIFY DEVICE
Error 2032 occurred at disk power-on lifetime: 424 hours (17 days + 16 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
04 61 46 00 00 00 a0 Device Fault; Error: ABRT
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
ef 03 46 00 00 00 a0 00 2d+13:04:28.794 SET FEATURES [Set transfer mode]
ef 10 02 00 00 00 a0 00 2d+13:04:28.794 SET FEATURES [Enable SATA feature]
ec 00 00 00 00 00 a0 00 2d+13:04:28.793 IDENTIFY DEVICE
c8 00 08 00 00 00 e0 00 2d+13:04:28.779 READ DMA
ef 10 02 00 00 00 a0 00 2d+13:04:28.779 SET FEATURES [Enable SATA feature]
Error 2031 occurred at disk power-on lifetime: 424 hours (17 days + 16 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
04 61 02 00 00 00 a0 Device Fault; Error: ABRT
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
ef 10 02 00 00 00 a0 00 2d+13:04:28.794 SET FEATURES [Enable SATA feature]
ec 00 00 00 00 00 a0 00 2d+13:04:28.793 IDENTIFY DEVICE
c8 00 08 00 00 00 e0 00 2d+13:04:28.779 READ DMA
ef 10 02 00 00 00 a0 00 2d+13:04:28.779 SET FEATURES [Enable SATA feature]
ec 00 00 00 00 00 a0 00 2d+13:04:28.778 IDENTIFY DEVICE
Error 2030 occurred at disk power-on lifetime: 424 hours (17 days + 16 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
04 61 08 00 00 00 e0 Device Fault; Error: ABRT 8 sectors at LBA = 0x00000000 = 0
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 08 00 00 00 e0 00 2d+13:04:28.779 READ DMA
ef 10 02 00 00 00 a0 00 2d+13:04:28.779 SET FEATURES [Enable SATA feature]
ec 00 00 00 00 00 a0 00 2d+13:04:28.778 IDENTIFY DEVICE
ef 03 46 00 00 00 a0 00 2d+13:04:28.778 SET FEATURES [Set transfer mode]
ef 10 02 00 00 00 a0 00 2d+13:04:28.778 SET FEATURES [Enable SATA feature]
Error 2029 occurred at disk power-on lifetime: 424 hours (17 days + 16 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
04 61 02 00 00 00 a0 Device Fault; Error: ABRT
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
ef 10 02 00 00 00 a0 00 2d+13:04:28.779 SET FEATURES [Enable SATA feature]
ec 00 00 00 00 00 a0 00 2d+13:04:28.778 IDENTIFY DEVICE
ef 03 46 00 00 00 a0 00 2d+13:04:28.778 SET FEATURES [Set transfer mode]
ef 10 02 00 00 00 a0 00 2d+13:04:28.778 SET FEATURES [Enable SATA feature]
ec 00 00 00 00 00 a0 00 2d+13:04:28.777 IDENTIFY DEVICE
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
WD-WCC4N5EKLTNX
smartctl 6.6 2017-11-05 r4594 [x86_64-linux-4.19.0-9-amd64] (local build)
Copyright (C) 2002-17, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Western Digital Red
Device Model: WDC WD30EFRX-68EUZN0
Serial Number: WD-WCC4N5EKLTNX
LU WWN Device Id: 5 0014ee 2bb548051
Firmware Version: 82.00A82
User Capacity: 3,000,592,982,016 bytes [3.00 TB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Rotation Rate: 5400 rpm
Device is: In smartctl database [for details use: -P show]
ATA Version is: ACS-2 (minor revision not indicated)
SATA Version is: SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is: Sat Jun 20 08:50:48 2020 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: (39540) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 397) minutes.
Conveyance self-test routine
recommended polling time: ( 5) minutes.
SCT capabilities: (0x703d) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x002f 200 200 051 Pre-fail Always - 0
3 Spin_Up_Time 0x0027 180 179 021 Pre-fail Always - 5975
4 Start_Stop_Count 0x0032 100 100 000 Old_age Always - 32
5 Reallocated_Sector_Ct 0x0033 200 200 140 Pre-fail Always - 0
7 Seek_Error_Rate 0x002e 100 253 000 Old_age Always - 0
9 Power_On_Hours 0x0032 097 097 000 Old_age Always - 2443
10 Spin_Retry_Count 0x0032 100 253 000 Old_age Always - 0
11 Calibration_Retry_Count 0x0032 100 253 000 Old_age Always - 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 31
192 Power-Off_Retract_Count 0x0032 200 200 000 Old_age Always - 4
193 Load_Cycle_Count 0x0032 200 200 000 Old_age Always - 2443
194 Temperature_Celsius 0x0022 115 107 000 Old_age Always - 35
196 Reallocated_Event_Count 0x0032 200 200 000 Old_age Always - 0
197 Current_Pending_Sector 0x0032 200 200 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0030 100 253 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x0032 200 200 000 Old_age Always - 0
200 Multi_Zone_Error_Rate 0x0008 100 253 000 Old_age Offline - 0
SMART Error Log Version: 1
ATA Error Count: 45 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 45 occurred at disk power-on lifetime: 2416 hours (100 days + 16 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
04 61 02 00 00 00 a0 Device Fault; Error: ABRT
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
ef 10 02 00 00 00 a0 08 04:26:20.066 SET FEATURES [Enable SATA feature]
ec 00 00 00 00 00 a0 08 04:26:20.066 IDENTIFY DEVICE
ef 03 46 00 00 00 a0 08 04:26:20.066 SET FEATURES [Set transfer mode]
ef 10 02 00 00 00 a0 08 04:26:20.065 SET FEATURES [Enable SATA feature]
ec 00 00 00 00 00 a0 08 04:26:20.065 IDENTIFY DEVICE
Error 44 occurred at disk power-on lifetime: 2416 hours (100 days + 16 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
04 61 46 00 00 00 a0 Device Fault; Error: ABRT
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
ef 03 46 00 00 00 a0 08 04:26:20.066 SET FEATURES [Set transfer mode]
ef 10 02 00 00 00 a0 08 04:26:20.065 SET FEATURES [Enable SATA feature]
ec 00 00 00 00 00 a0 08 04:26:20.065 IDENTIFY DEVICE
ef 10 02 00 00 00 a0 08 04:26:20.046 SET FEATURES [Enable SATA feature]
Error 43 occurred at disk power-on lifetime: 2416 hours (100 days + 16 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
04 61 02 00 00 00 a0 Device Fault; Error: ABRT
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
ef 10 02 00 00 00 a0 08 04:26:20.065 SET FEATURES [Enable SATA feature]
ec 00 00 00 00 00 a0 08 04:26:20.065 IDENTIFY DEVICE
ef 10 02 00 00 00 a0 08 04:26:20.046 SET FEATURES [Enable SATA feature]
ec 00 00 00 00 00 a0 08 04:26:20.046 IDENTIFY DEVICE
Error 42 occurred at disk power-on lifetime: 2416 hours (100 days + 16 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
04 61 02 00 00 00 a0 Device Fault; Error: ABRT
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
ef 10 02 00 00 00 a0 08 04:26:20.046 SET FEATURES [Enable SATA feature]
ec 00 00 00 00 00 a0 08 04:26:20.046 IDENTIFY DEVICE
ef 03 46 00 00 00 a0 08 04:26:20.046 SET FEATURES [Set transfer mode]
ef 10 02 00 00 00 a0 08 04:26:20.045 SET FEATURES [Enable SATA feature]
ec 00 00 00 00 00 a0 08 04:26:20.045 IDENTIFY DEVICE
Error 41 occurred at disk power-on lifetime: 2416 hours (100 days + 16 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
04 61 46 00 00 00 a0 Device Fault; Error: ABRT
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
ef 03 46 00 00 00 a0 08 04:26:20.046 SET FEATURES [Set transfer mode]
ef 10 02 00 00 00 a0 08 04:26:20.045 SET FEATURES [Enable SATA feature]
ec 00 00 00 00 00 a0 08 04:26:20.045 IDENTIFY DEVICE
ef 10 02 00 00 00 a0 08 04:26:20.030 SET FEATURES [Enable SATA feature]
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
保証
どちらのドライブも保証が適用されるため、故障が証明されたら交換できます。
ベストアンサー1
SATAケーブル交換後（特にSATA v1ケーブル）
それでは、2本のSATAケーブルを交換した後、正確に何が起こりましたか？
まず、私の質問で述べたように、エラーなしで両方のドライブを読みました！
第二に、これらのエラーが書き込み関連である可能性があることを知って、書き込みテストを実行しました！
下の画像はより大きな解像度を持っています。拡大するにはクリックしてください。
もはや見られるエラーがないことを直接確認することができ、dmesgこれは私を喜ばせ、私の理論を証明します。サーバーを構築するとき、そのケーブルがどれくらい古いかわからなかったので、悲しかったです。とにかく問題は一時的に解決されました。