Linux MintでWi-Fiが機能しない

Linux MintでWi-Fiが機能しない

私は過去4年間にUbuntu(複数バージョン)を実行してきたDell Latitude E4310ノートブックを持っています。最近Linux Mint(バージョン17)をインストールしましたが、WiFiが機能しませんでした。 Ubuntuでは完璧に動作します。

どうすればいいですか?インストールする必要があるドライバまたはパッケージはありますか?これが出力ですlspci

00:00.0 Host bridge: Intel Corporation Core Processor DRAM Controller (rev 02)
00:02.0 VGA compatible controller: Intel Corporation Core Processor Integrated Graphics Controller (rev 02)
00:19.0 Ethernet controller: Intel Corporation 82577LM Gigabit Network Connection (rev 05)
00:1a.0 USB controller: Intel Corporation 5 Series/3400 Series Chipset USB2 Enhanced Host Controller (rev 05)
00:1b.0 Audio device: Intel Corporation 5 Series/3400 Series Chipset High Definition Audio (rev 05)
00:1c.0 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 1 (rev 05)
00:1c.1 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 2 (rev 05)
00:1c.2 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 3 (rev 05)
00:1c.3 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 4 (rev 05)
00:1d.0 USB controller: Intel Corporation 5 Series/3400 Series Chipset USB2 Enhanced Host Controller (rev 05)
00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev a5)
00:1f.0 ISA bridge: Intel Corporation 5 Series/3400 Series Chipset LPC Interface Controller (rev 05)
00:1f.2 RAID bus controller: Intel Corporation 82801 Mobile SATA Controller [RAID mode] (rev 05)
00:1f.3 SMBus: Intel Corporation 5 Series/3400 Series Chipset SMBus Controller (rev 05)
00:1f.6 Signal processing controller: Intel Corporation 5 Series/3400 Series Chipset Thermal Subsystem (rev 05)
02:00.0 Network controller: Intel Corporation Centrino Advanced-N 6200 (rev 35)
03:00.0 SD Host controller: Ricoh Co Ltd MMC/SD Host Controller (rev 01)
3f:00.0 Host bridge: Intel Corporation Core Processor QuickPath Architecture Generic Non-core Registers (rev 02)
3f:00.1 Host bridge: Intel Corporation Core Processor QuickPath Architecture System Address Decoder (rev 02)
3f:02.0 Host bridge: Intel Corporation Core Processor QPI Link 0 (rev 02)
3f:02.1 Host bridge: Intel Corporation Core Processor QPI Physical 0 (rev 02)
3f:02.2 Host bridge: Intel Corporation Core Processor Reserved (rev 02)
3f:02.3 Host bridge: Intel Corporation Core Processor Reserved (rev 02)

また、以下を実行しますservice networking restart

davidlat ~ # service networking restart
stop: Job failed while stopping
start: Job is already running: networking
davidlat ~ # 

更新:結果は次のとおりです。ifconfig -a

davidlat ~ # ifconfig -a
eth0      Link encap:Ethernet  HWaddr 5c:26:0a:0c:9c:1c  
          inet addr:10.0.0.13  Bcast:10.0.0.255  Mask:255.255.255.0
          inet6 addr: fe80::5e26:aff:fe0c:9c1c/64 Scope:Link
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:804913 errors:0 dropped:0 overruns:0 frame:0
          TX packets:393747 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000 
          RX bytes:1066394980 (1.0 GB)  TX bytes:37366404 (37.3 MB)
          Interrupt:20 Memory:f5400000-f5420000 

lo        Link encap:Local Loopback  
          inet addr:127.0.0.1  Mask:255.0.0.0
          inet6 addr: ::1/128 Scope:Host
          UP LOOPBACK RUNNING  MTU:65536  Metric:1
          RX packets:32255 errors:0 dropped:0 overruns:0 frame:0
          TX packets:32255 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0 
          RX bytes:3728961 (3.7 MB)  TX bytes:3728961 (3.7 MB)

wlan0     Link encap:Ethernet  HWaddr 00:27:10:92:61:28  
          BROADCAST MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000 
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)

ベストアンサー1

wpa_supplicantとdhclientを介してWi-Fiに手動で接続してみてください。次のコマンドを実行する必要があります。

wpa_passphrase ssid password > /etc/wpa_supplicant.conf
wpa_supplicant -Dwext -iwlan0 -c /etc/wpa_supplicant.conf
dhclient wlan0

ssid=Wi-Fi名

wpa_supplicantを実行してから接続するのを待ってからbg(ctrl + z; bg)に移動するか、別の端末を使用してdhclientを実行します。

おすすめ記事